end cover

For receiving said lock pin stretching inward from the casing and said end cover, at least one first and one second positions are limited.

A motor shaft gap used for a sealing plate for a seal air channel is left between the belt pulley and the end cover of the motor shell.

the inner cavity of the front end cover filled with circulating water or compressed air to cool the bearings.

the upper end cover is provided with a horn-shaped air outlet hole on the other end of the air groove.

A safety valve with an air overflowing through hole is arranged on one end cover of the top of the barrel body.

A vertical flange used for installing the motor is arranged at an end cover or a motor shell close to the impeller inducer end.

and general working procedure of packing rotor into the machine seat and installing the front and back end cover and other parts.

The front end cover and the rear end cover are fixed by screws and rabbets. Meanwhile, the rotor assembly is fixed.

Said casing receives concentricity the neck of end cover for sealing one end of the tube body.

A cavity formed by a run-through hollow tube of an end cover is arranged at one end of the faucet main body.

the seal washer is positioned between the shell body and the end cover and is O-shaped self-tightening seal structure.

The material component, technology, structure and performance of the steel casting end cover are studied.

and the ring flute is composed of two ring coaxial protruding ribs protruded on the end face of the end cover.

The pump body consists of pump housing, anterior end cover, rear end cover, anterior impeller, rear impeller, and permanent magnet as rotor.

Since the pump inlet is through the end cover, pump starvation is minimized.

A concave groove is arranged outside the conical shell, the large-end end surface of the shell is provided with a pressure spring end cover.

Remove motor shaft end cover. Apply hand winding crank to the squared end of motor shaft.

Don't you see the frame? Its temple is made of memory metal, the end cover is made of the board of resin, and the quality is very nice.

The phototransistor and the light emitting diode are arranged on the end cover along a radical direction to form a measurement head.

due to the effect of the protruding ribs, the rubber ring is unlikely to separate from the end cover when receiving a side force.

A fan is additionally arranged on the end cover part of the voltage-stabilizing voltage regulator.

the lower-half end cover at one side is provided with an oil inlet and the upper-half end cover is provided with an oil outlet.

The finished distributor drive housing (L) and camshaft end cover is shown before and after it is split.

The end cover switch is loosened, a circuit is cut off, and the electric flash device stops flashing.

Put it into the vagina, the closed end cover in the cervix.

the end cover 2 of the inclosed cavity is connected with a metal filter core.

If the end cover port is used as the inlet port, the internal "drag" is reduced.

It also has an end cover port.

Casting Process Simulation of the Ball Milling Machine End Cover

The utility model relates to a lamp holder in particular to a high-pressure discharge lamp and comprises a case body and an end cover;

the front and back end cover which covers the shell;

A roll is arranged at the junction of the end cover, and a fixed stage is arranged on the cylinder;

The sample probes makes of the insulation material, its peak is equipped with the belt end cover the sample chamber;

the lower end cover of the gas cylinder is not only used to support and seal, but also used to be bearing chock;

the center of the end cover body is provided with an installation through hole;

Digital Control Lathe Processing Technology for Small Electric Machine End Cover

Design of a Special Cutting Tools -array for Motor End Cover

Design of the side wall forming die for end cover

Improvement of the Installing Technique of the Bearing End Cover of Motor

the end cover is provided with a spark plug (8) on the position between two adjacent circular teeth of the circular arc gear ring (3);

Key technique in stamping convex positioned micromotor end cover

Procedure of Casting and Heat-treatment for End Cover Casting of large Coal Pulverizer

The Stamping Forming Key Technique on End-cover in Micro Electric Motor

Forming Technique and Design of Die for Titanium Alloy End Cover Part

Cause Analysis of End- cover Blowup of Deaerator Water Tank

New Method for Efficient Cutting End Cover Parts

Forming Technology and Die Design for End Cover

Cracks Re-welding Process on Ball Mill Feed End Cover

Remedy of Fatigue Crack in End Cover of Tube Mill

Fig. 1 Load distribution on ellipsoidal end cover

Crack on End Cover of Mill Cylinder