test specimen

The test specimen shall be immersed in the measuring electrolyte so that the top edge of the area to be measured is level with the surface.

The surface of the test specimen must be clean and free from defects.

Test specimen shall be dissolved with acid. The solution shall be used for analyzing calcium and Barium.

If the test specimen is in the form of large crystals, reduce the particle size to about 2 mm by quickly crushing.

A corresponding analytical system named TDGS was proved to be quite effective in simulating a prototype test specimen.

This paper presents a method in which the content of calcium and barium all be measured with only one test specimen dissolution.

The spectral reflectance of each test specimen is measured in situ before and after exposures.

The injection molding technology of PEEK was studied with a test specimen mold.

RUBBER. TEST SPECIMEN. CONTROLLED ATMOSPHERES. TEST ATMOSPHERES.

Pour the remaining liquid from the test specimen at the end of each cycle.

It's concluded that the beef tail hair can be used as the test specimen to replace beef tissues.

According to the processing performance titanium alloy materials, using a CNC machining center processing the tensile test specimen.

Mark the water level on the side wall of the test specimen.

In this test, a test specimen consists of one fiber encapsulated in the polymer matrix in a dog bone shape.

any test specimen that displays escalating combustion behaviour so that it is unsafe to continue the test and requires forcible extinction.

The test specimen may be titrated with the Reagent directly, or the analysis may be carried out by a residual titration procedure.

The specimens may not drip flaming particles that ignite the dry absorbent surgical cotton located 300 mm below the test specimen.

Wash the test specimen in warm water using the mild dish detergent solution until adhering salt deposits are completely removed.

With the block blocking the most unstable side of the specimen legs to prevent the test specimen to move.

The following tests and measurements shall be performed on the same test specimen.

Visually examine test specimen for defects and record on reference diagram.

The specimens can drip flaming particles that ignite the dry absorbent surgical cotton located 300 mm below the test specimen.

GLASS. BEND TEST OF A DUAL-GLASS TEST SPECIMEN.

Figure 4 shows the instrumentation of the test specimen (test object). The wall of the specimen was 12. 5 mm thick.

Is a wedge test specimen utilized for chill or analysis control?

Draw a diagram of the test specimen surface.

In part this is for safety reasons, in part because we do not want to fail a test specimen or overload an instrument.

Report efflux time to the nearest 0. 2 seconds, the Zahn--cup used, and the temperature of the test specimen.

The titration of water is usually carried out with the use of anhydrous methanol as the solvent for the test specimen;

hold the test specimen by the edges at an angle above the pre - cleaned microscope slide . the specimens should not touch the slide

Test Method for Measurement of Smoke Obscuration Using in a Single Closed Chamber, with the Test Specimen Oriented Horizontally

Thermoplastic roofing and sealing sheets; determination of tear resistance; trapezoidal test specimen method

Destructive tests on welds in metallic materials - Impact tests - Test specimen location, notch orientation and examination

Acoustics - Measurement of sound absorption in a reverberation room; Amendment 1: Test specimen mountings for sound absorption tests

Adhesives, T peel strength test method for a flexible-to-flexible test specimen assembly

Effect of Methods to Prepare Full-section Tension Test Specimen for Aluminium Extruded Tubes on Obtained Tensile Properties

Uniformity examination and determination to cement ability test specimen

Fabrication method of ring test specimen for filament -winding reinforced plastics

any test specimen that burns until it is essentially consumed within the test duration;

Experimental Study and Numerical Simulation of Creep Damage of Small Punch Creep Test Specimen of SS304 Stainless Steel

Research on Design of Test Specimen for Impedance Measurement of Elastic Pipe

Adhesives; peel test for a flexible-bonded-to-rigid test specimen assembly; part 2: 180? peel

Adhesives; peel test for a flexible-bonded-to-rigid test specimen assembly; part 1: 90? peel

Preparation of standard test specimen of feed- grade dicalcium phosphate

As = Measured absorbance of test specimen

notched-bar impact bending test specimen

for flaming ignition sources 4 and 5: any test specimen that continues to flame for more than 10 min after ignition of the crib;