单词 | injection speed |
释义 | 例句释义: 注射速度,射出速度,注塑速度,压射速度 1. Excessively high injection speed can cause high surface orientation and increase susceptibility to stress cracking. 过高的注塑速度会引起较高的表面方向性及增加应力破裂的敏感性。 www.mapeng.net 2. Adaptive control in tracking the constant injection speed the error decrease slowly, the track occurs and dithering when the speed changes. 自适应控制在跟踪恒定注射速度时误差减小较慢,在速度发生突变时的跟踪容易发生超调和抖动。 www.13191.com 3. Rate of pressure drop (controlled primarily by injection speed) ? 压降的减少(主要控制由注射速度) wenku.baidu.com 4. Injection Speed affects the viscosity of the molten material. 注射速度影响熔体粘度 wenku.baidu.com 5. Injection speed may be too slow causing freezing before mold is filled. 即计量太小)注射速度太小导致充填结束之前树脂凝固。 www.mouldbbs.com 6. It also showed the depressor effect of Shuanghuanglian Injection was affected by injection speed and concentration. 同时表明注射速度和浓度直接影响双黄连注射剂的降压作用强度。 www.bing.com 7. According to the products and raw materials appropriate injection pressure and adjust injection speed. 根据制品及原料调整适当打针压力及打针速度。 www.lifengsuye.com 8. Thus, in conditions permit, it can be an appropriate increase injection speed, speed up the development of condensate gas reservoir. 因此,在条件允许的情况下,可以适当提高注采速度,加速凝析气藏的注气开发。 lib.swpu.edu.cn 9. The screw rod advances the melt body the speed to call the injection speed, its calls the injection speed; 螺杆推进熔体地速度称打针速度,其流率称打针速度; www.izgc.net 10. Try to maintain an even, rapid melt flow Increase injection speed Raise melt temperature Raise mould temperature Increase wall thickness 尽量保持均匀和快速的熔体流动注射速度太低提高熔体温度提高模具温度增大壁厚 wenku.baidu.com 1. Clamping Stroke Clamping Unit Mold Opening Mold Closing Speed Injection Speed Injection Capacity Charging Charging Stroke Rib 合模行程锁模装置开模合模速度射出速度注塑量计量计量行程骨位、筋位、加强筋 wenku.baidu.com 2. Equal Accelerating Control of the Injection Speed of the Cold Chamber Die-casting Machine 冷室压铸机压射速度的匀加速控制 ilib.cn 3. General principles when setting injection speed or injection time 注射速度和注射时间设定的一般原则 www.6sqm.net 4. Excessively High Injection Pressure and Injection Speed is Too Fast 啤塑壓力過高,蜱塑速度太快 wenku.baidu.com 5. Reduce injection speed or adjust injection profile (slow then fast) 减速或者调整注塑面(先慢后快)? wenku.baidu.com 6. Delay switching injection speed to holding pressure 延迟从注塑到保压的切换 rhodia-ep.com.cn 7. Improve injection speed and holding time or pressure 改善注塑速度和保压压力或时间 rhodia-ep.com.cn 8. Low molding pressure with high injection speed 高射速低射压 wenku.baidu.com 9. resin injection speed injection unit 注射速度注塑装置 wenku.baidu.com 10. High injection speed for low filling pressure 高射速低注射压 wenku.baidu.com 1. Excessively High or low Injection Speed 過高或過低的注射速度 wenku.baidu.com 2. Excessively High of Low Injection Speed 注射溫度過高或過低 wenku.baidu.com |
随便看 |
|
英汉双解词典包含2704715条英汉词条,基本涵盖了全部常用单词的翻译及用法,是英语学习的有利工具。