The impact point of the ice floes at the propeller blade is usually in the upper part of the blade near the bearings.

When a new blade is plugged in, it will install the firmware version from the primary blade, copy all of its settings, and begin processing traffic within minutes.

Use a vacuum or can of compressed air with a nozzle around the area of the cutter blade to remove any dust or debris.

In this load situation, the section modulus of the blade profile is at its highest, which reduces the risk of damage.

Any port on any blade can be used for any application, so the system can be wired for redundancy and simplicity.

The magnitude of the bending moment has a significant influence on the service life of the propeller blades.

Therefore, I think that the two blades of this sword should be as balanced as a scale, so that people in the trade will receive assistance on the one hand, and being regulated on the other.

When repair or replacement of the cord or plug is required, do not connect the grounding wire to either flat blade terminal.

If necessary to assist turning, wedge a screwdriver blade between the screw heads and the hex cap of air valve (5).

The high speed rotor blade and timer control ensure reliable, fast and reproducible sample preparation in under ten seconds.

Adhesive oil must be cleaned from the blade and guides with a dry cloth to prevent dust attraction.

Blade Servers: Blade servers consume about 10 percent less power than equivalent rack mount servers thanks to multiple servers sharing common power supplies, cooling fans and other components.

The influence of pressure gradients on the two-phase flow between the blades if the turbine prototype differs from the turbine model.

Leaves alternate, to 50 cm; petiole and rachis lepidote or glabrous; petiolules 1-15 mm, sometimes slightly inflated, sparsely to densely lepidote, sometimes glabrescent; leaflets 3-9, alternate to subopposite; leaflet blades elliptic, oblong, ovate-lanceolate, or lanceolate, 5-20(-30) × 2-7.5(-11.5) cm, papery to leathery, both surfaces glabrous or adaxially lepidote only on midvein and abaxially lepidote on veins only or on entire surface, midvein abaxially prominent and adaxially depressed, secondary veins (8-)12-15(-16) on each side of midvein, abaxially prominent or depressed, and adaxially flat, prominent, or depressed, base rounded or ± oblique by being cuneate and conspicuously decurrent on one side and rounded on other, apex acuminate to obtuse.

An OEM customer asked Hydratight to design a multi-stud tensioning device which was capable of simultaneously tensioning up to 88 bolts, to be used to connect a 38 metre long blade to a bearing slew ring.

For the optimum efficiency of these types of turbines the relationship between wicket gates opening and runner blades position (Cam Curve) as a function of various operating parameters is determined by model tests, index tests or calculations.

For the first time a fully heated wiper blade is available as an option that prevents snow or ice from forming on the blade in winter.

Rheometers can be used to simulate a variety of gravure, blade, slot die systems to accurately quantify the coating properties of adhesives and sealants using just small sample volumes.

Recess under guide plates provides blade clearance at end of stroke.

Other new features include the unique Frontbass system, which turns the luxury sports car into a concert hall regardless of whether the top is open or closed, and the highly efficient adaptive windscreen wipe/wash system MAGIC VISION CONTROL; it supplies water from the wiper blade as required and depending on the direction of wipe.

Database, email and virtualization servers for blade, rack or tower systems.

As an example, the Committee was informed that most metal blades have a fixed life or time before overhaul, which is typically in the range of 3,000 to 6,000 hours but at UNAMID can be as low as 1,800 hours.

Therefore, under a defective political system, any measure to upgrade the powers and responsibilities of DCs might, on the contrary, become a sharp blade that would jeopardize the living environment of the districts.

For example, tools (drills, screwdrivers, saw blades, etc.) and machine parts are coated to improve their wear resistance, electric and dielectric (insulating) layers are deposited in semiconductor and solar cell manufacturing processes, the heat insulation of glazing is improved by a coating applied to its surface and the humidity in reactor/process chambers is controlled to ensure optimum performance.

Huntsman Performance Products makes JEFFAMINE® polyetheramines (PEAs) and supplies them to Huntsman’s Advanced Materials division for their Araldite® epoxy resin systems and to other global and regional system formulators that manufacture their own epoxy resin systems needed to make the rotor blades on the wind-turbine generators.

Tomorrow, reduced-footprint Savvio-enabled storage arrays would allow 70% more IOPS in a smaller space than many existing arrays, or 150% more IOPS/U. For those designing blade servers, Savvio disc drives enable high duty cycle enterprise-class computing on each individual server blade.