▾

External sources (not reviewed)

Connecting the coupler too early [...] [...]

Install pivot plate (A) on pivot and tighten two screws on pivot plate.

Remove two screws on pivot plate (A), swivel shaft (B) if necessary, and remove coupling (C) from swivel shaft.

Turn connecting rod (14) to align [...]

The ganged multicoax solution MXP offers a true 40 GHz/ 40 Gbps coaxial-to-PCB transition with a very small form factor.

[...] actual number of conversions of fixed-term contracts to continuing contracts in connection [...]

[...] indexing on the rotary axes, achieving speed and precision far surpassing those of conventional 5-axis control machines.

[...] [...] customers can do continuous operation and setups with peace of mind.

[...] requires neither axle nor shaft or gearing.

Available in standard and food-grade paint ball-screw configurations, these new actuators extend the maximum feed force ratings up to 14,679 N (3300 lb) and system continuous stall force ratings up to 13,122 N (2950 lb).

[...] our NMV Series of 5-axis control vertical machining [...]

HUBER+SUHNER BNT triaxial connectors are RF connectors with a bayonet coupling mechanism and three concentric contacts (inner conductor, inner screen and outer screen) for triaxial cables.

[...] vertical shaft rotation through gearing, material goes into powder selecting room through feeding port set on the upper of powder selecting machine chamber, and falls on the spreading plate through flux powder pipe and the space between the up cone and the down cone set in the coarse powder collecting cone, and spreading plate rotates follows vertical [...] [...]

[...] [...] accuracy to the rotary axis assembly by [...]

[...] [...] toward a larger-scale conversion project (replacement [...] [...]

The cable connectors also emit an audible click when mated to the JSC coaxial board mounted connector (MM5829-2700).

[...] completed including connectors, switches, cables, [...] [...]

Connect a Swagelok union elbow or tee to the adapter by tightening the Swagelok tube fitting with a wrench, while holding the elbow or tee in the desired direction.

[...] [...] the tilting-type rotary axis and high-precision [...]

Operate the on-load tap-changer poles separately by one step by rotating the shaft ends counter-clockwise until the diverter switch operates once.

[...] [...] with an integral rotary shaft seal, a gasket [...] [...]

Standard techniques for interventional vascular procedures should be employed • Manipulation of the Zilver PTX Drug-Eluting Peripheral Stent requires fluoroscopic control • Do not try to remove the stent from the introducer system before use • Ensure that the red safety lock is not inadvertently removed until final stent release • Deploy the stent over an extra stiff or ultra stiff wire guide • Do not push the hub toward the handle during deployment • Do not expose the delivery system to organic solvents (e.g., alcohol) • Do not use power injection systems with the delivery system • Do not rotate any part of the system during deployment • The device is intended for single use only.

See the instructions starting on the next page for installation of Swagelok tube fittings, O-seal male connectors, caps and plugs, port connectors, tube adapters, positionable elbows and tees, weld fittings, depth marking tool, and preswaging tool.

[...] may attempt to rotate the bearing, affecting [...]

[...] [...] translated into two consecutive C/5 Programme documents [...] [...]

To make development more equitable, effective and efficient by bridging the existing gap between commitment and practice, there is a need to translate the common goals, objectives and principles of the Convention, the World Programme of Action and the Standard Rules into cohesive national action that incorporates the disability perspective into development policies, programmes and relevant projects and activities.

To send advertising or soliciting emails, without prior permission, to other students, tutors, other third parties or our Company, to send emails that would give a feeling of disgust, to interrupt mail reception of others, to request a third party to forward chain-reaction emails, or to forward such emails complying with requests.

[...] [...] of maximum spindle speed and whether there is Spindle 2.