| 单词 | 弯矩 | ||||||||||||||||||||||||||||
| 释义 | 弯矩 noun —bending moment n弯弯 noun —bark ntriangle nSee also:弯 n—bend n 矩 adj—rectangular adj 矩 n—rectangles n • rule n 矩—pattern • carpenter's square 弯—bent
|
这些夹具需要足够结构刚度，从而克服较 大 弯矩 和 振 动本身带来的影响。 bksv.cn | These fixtures need to be designed [...] with sufficient structural rigidity to [...] overcome the large bending moments and the effects [...]of the vibration regime itself. bksv.ru |
按照ASMEQME-1核电厂能动机械设备鉴定中有关端部加载试验的规定，确定外部载荷的施加方式（ 即 弯矩 通 过 阀杆中心平面，拉力和压力施加于管道中心线），根据ASMEQME-1和ASME核动力装置制造准则，以管道材料屈服时的外部弯曲载荷、外部拉伸载荷和外部压缩载荷作为有限元分析的试加载荷值，这个值也作为复合载荷设计分析的依据。 tvi.cn | Dynamic mechanical equipment identification in accordance with the ASMEQME-1 nuclear power plant about the end of the [...] load test requirements, the external load is [...] applied (ie the moment through the stem [...]center plane, tension and pressure is applied [...]to the pipe centerline), according to ASMEQME-1 and the ASME nuclear power plant manufacturing standards, external piping material yield bending loads, external tensile load and external compression test load as finite element analysis plus load value, this value is also designed as a composite load analysis based on. tvi.cn |
弯曲力矩的大 小对螺旋桨叶片的使用寿命有很大的影响。 voith.com | The magnitude of the bending moment has a significant [...] influence on the service life of the propeller blades. voith.com |
最大允许外部主轴负载（Re） 可由下面允许轴向负载表中给出的最大 允许弯曲力矩（Me）计算得出，外部 负载作用方向见右边外部负载作用方向 图。 sauer-danfoss.com | If continuous applied radial loads exceed 25% of the maximum allowable or thrust (axial) loads are present, contact your Sauer-Danfoss representative for a bearing life evaluation. sauer-danfoss.com |
本田表示，车辆转弯时，后轮内侧产生的能量通过电子方式恢复并施加到后轮外侧，为车辆“自我产生”必要的 转 矩 以 进行 转 弯。 cn.drivelinenews.com | In a turn, says Honda, the energy generated by the inside rear wheel is recovered [...] electrically and applied to the outside rear wheel to [...] “self-generate” the torque necessary for the vehicle [...]to make the turn. drivelinenews.com |
这样、只要储备各种尺寸 和材料的联合弯头和 联合三通接头 —— 以及常用的世伟洛克转换接头即可、没有必 要再储备特殊的弯头和三通。 swagelok.com | So, stocking union elbows and union tees in various sizes and materials—along with commonly used Swagelok adapters—eliminates the need for stocking special elbows and tees. swagelok.com |
矩阵表中的数字与 零配件图与清单中的参考号不同。 graco.com | The digits in the matrix do not correspond [...] to the reference numbers in the Parts drawings and lists. graco.com |
与传统的力矩电机相比，分段设 计能最大的提高经济效率并使用户接受，因为它速度高和易于维修。 schaeffler.cn | Compared to conventional torque motors, the segment [...] design offers the greatest possible economic efficiency and convinces [...]users because of its high speeds and easy maintenance. schaeffler.cn |
设计指南还包含各类驱动器和电机 / [...] 执行器组合中推荐使用的电机电缆、性能技术参数以及 转矩 / 速度 ( 旋转 ) 和力 / 速度 ( [...]直线 ) 曲线。 literature.rock...lautomation.com | The design guides also include the [...] recommended motor cables, performance [...] specifications, and torque/speed (rotary) [...]and force/velocity (linear) curves for each [...]drive and motor/actuator combination. emea.rockwellautomation.com |
其改进的弯曲性能 可预防由紧密弯曲造 成的损耗增加现象，从而帮助提高系统可靠性，最大限度延长网络正常运行时 间。 furukawa.co.jp | Its improved bend performance can guard against instances of higher loss caused by tight bends, thus helping [...] to increase systems [...]reliability and to maximize network uptime. furukawa.co.jp |
下图所示的使用方法会 使活塞杆产生极大的弯曲应 力，必须绝对禁止。 kosmek.co.jp | Never operate it in the way as shown in the drawing below as the piston rod [...] suffers from large bending stress. kosmek.co.jp |
高精密轴加工的其他有用的选项包括液压稳定支撑装置（可以最大限度地减少轴的颤动 和 弯 曲 ） 和曲轴 加工规格。 moriseiki.com | Other useful options for high-precision shaft machining [...] include the hydraulic steady rest, which [...] minimizes chatter and bending of shafts, and specifications [...]for crankshaft machining. moriseiki.com |
不得使用弯曲、损坏或破损的电极。 graco.com | Do not operate the [...] spray gun with a bent, damaged or [...]missing electrode. graco.com |
Bandera接着又对变速箱进行了深入分析，分别阐述了标准模式（“如果检测到处于运动型驾驶风格，将进行高转速换挡”）和运动模式（“进行高转速换挡；如果为了让进弯更方便并保持 出 弯 时 的 良好 扭 矩 而 调整转速范围，此时将选择最低挡位”），以及自动模式、冰雪模式和手动模式。 maserati.com.cn | Bandera then provides an in-depth look at the transmission, from Normal mode (“if a sporty driving style is detected, gear changes are made at higher revs”), to Sport mode (“gear changes are made very high up on the rev range; the lowest gear is selected when scaling the range to make going into corners easier and ensure good torque coming out”). maserati.it |
英汉双解词典包含2273206条英汉词条，基本涵盖了全部常用单词的翻译及用法，是英语学习的有利工具。