| 单词 | 内螺纹 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 释义 | 内螺纹 noun —female thread nSee also:螺纹—thread of screw • whorl of fingerprint • spiral pattern 螺—conch • snail • spiral shell 纹—line • pattern • trace • grain (of wood etc) 纹 n—wrinkles n • mark n
|
然 后将这个转换接头或三通接头 依靠螺纹旋入至取样钢瓶的内 螺纹端口。 swagelok.com | This adapter or tee is then threaded into the female port of a sample cylinder. swagelok.com |
紧 固 O 型圈密封连接直到其与内螺纹端的 表面形成金属至金属的接触。 swagelok.com | Tighten the O-seal connector until it makes metal-to-metal contact with the face of the female end. swagelok.com |
把 O 型圈密封连接旋入内螺纹端直 到已用手指拧紧。 swagelok.com | Turn the O-seal connector into the female end until it is finger-tight. swagelok.com |
若要相同公称尺寸的内螺纹和外 螺纹拥有相 同的压力额定值、内螺纹往往 需要更厚的管壁、可能会造成接头 过大和过于笨重以至于无法使用。 swagelok.com | For female and [...] male pipe threads to have the same pressure rating in the same nominal pipe size, the female [...]thread would require a heavier [...]wall, resulting in a fitting too large and bulky to be practical. swagelok.com |
该发动机有一个 1 英寸 npt （内螺纹）液压回油接头。 graco.com | The motor has a [...] 1 in. npt(f) hydraulic oil return fitting. graco.com |
表格中列出了外螺纹和内螺纹 的锥螺纹端压力。 swagelok.com | The table lists pressure ratings for male and female tapered pipe thread ends. swagelok.com |
仅在内螺纹世伟 洛克端接中使用长变径接头。 swagelok.com | Use only long reducers in female Swagelok end connections. swagelok.com |
然 后 将 这 个 阀 依 靠 螺 纹 旋入取样钢瓶的内螺纹端口。 swagelok.com | The valve is then threaded into the female [...] port of a sample cylinder. swagelok.com |
在这些附件与 3/4 标准管螺纹 （内螺纹）泵空气入 口之间安装一个接地的柔性空气软管 (A)。 graco.com | Install a grounded, flexible air hose (A) between the accessories and the 3/4 npt(f) pump air inlet. graco.com |
在外螺纹螺母或接头本体六角与 内螺纹螺 母 接 合期间, 当垫片被两边的凸缘压紧时, VCR 组件上的密封即可完成。 swagelok.com.cn | The seal on a VCR assembly is made when the gasket is compressed by two beads during the engagement of a male nut or body hex [...] and a female nut swagelok.com.cn |
不过，丝杆上的键沟会导致蜗轮 内螺纹 的 磨损超出正常水平。 powerjacks.com | However the [...] keyway in the screw will cause greater than normal wear on the internal threads of the worm gear. powerjacks.com |
将溶剂供料管路连接至 1/4 npt （内螺纹）溶剂阀入口 （SVA 和 SVB）上。 gww.graco.com | Connect the solvent supply line to the 1/4 npt(f) solvent valve inlets (SVA and SVB). gww.graco.com |
将后撞击器带狭缝的一 端拧入喉管的内螺纹。 graco.com | Thread slotted end of rear impinger into female thread of throat. graco.com |
订购时, 选择一外螺纹 组件或内螺纹组件订购型号。 swagelok.com.cn | To order, select the ordering number for the male or female assemblies. swagelok.com.cn |
内螺纹插头 staubli.com | Plugs female thread staubli.com |
在 本 例 中 、安 装 工 作 要 求 把卡套管连接到一个内螺 纹端接。 swagelok.com | In this example, the installation requires connecting tubing to a female end connection. swagelok.com |
该装置设计用于带有标准外螺纹和 内螺纹螺 母 的 世伟洛克 VCR 金属垫片面密封组件上。 swagelok.com | This device is intended for use on Swagelok VCR metal gasket face [...] seal assemblies with standard male and female nuts swagelok.com |
安装于内螺纹上， 在相反方向及其 90°方向各有1支 配管。 smc.com.cn | Used for a branch line in the same [...] direction from female thread and in 90¡ directions. smc.co.nz |
该螺丝上面的螺丝孔除了可以固定六角螺丝刀外，还 有 内螺纹 ， 可 以连接另外的封闭螺丝。 sic-invent.com | For fixation of membranes or meshes [...] the primary cover [...] screw inside the hexagon has a thread hole to accept the screwdriver, which enables it to take an additional fixation screw. sic-invent.com |
安装在内螺纹上， 其反方向有分支配 管。 smc.com.cn | Used to branch line in the [...] same direction from female thread. smc.co.nz |
预装筒形模块确保安装人员正确安装卡套方向，目视检 查卡套的存在，并正确地安装到 内螺纹 本 体 上。 swagelok.com | The preassembled cartridge ensures [...] installers correct ferrule orientation, visual confirmation of ferrule presence, and proper [...] installation into the female body. swagelok.com |
可提供配套的直流 M8 3线推入 式直内螺纹连接。 swagelok.com.cn | A mating direct-current M8 3-wire push-on [...] straight female connector is available swagelok.com.cn |
世伟洛克中压卡套管接头和转换接头的简单两件式设计由一个 内螺纹接头 本体和一个预装筒形模块组成，预装筒形模块内包 含外螺纹螺母 和有颜色编码的前、后卡套，装在一个一次性塑 料轴上。 swagelok.com | The simple two-piece design of the Swagelok mediumpressure [...] tube fittings and [...] adapters consists of a female fitting body and preassembled cartridge containing the male nut and color-coded front and back ferrules [...]on a disposable plastic arbor. swagelok.com |
把一个世伟洛克外螺纹转 换接头的管螺纹连接接 入内螺纹端接。 swagelok.com | Tighten the pipe connection of a Swagelok male adapter into the female end connection. swagelok.com |
适配任何5/8''内螺纹的插孔，特别适合大力夹035。 manfrotto.cn | Fits any 5/8'' female sockets, works especially well with 035 Super Clamp. manfrotto.com |
罐呈管状立体构架设计，管焊接在 内螺纹 端。 zs.weirminerals.com | The drum is of a tubular space frame [...] design with box ends into which the tubes are welded. weirminerals.com |
J58-6300型离合器式电动螺旋压力机包括机架，安装在机架上方的驱动电机，由驱动电机带动的离合飞轮，安装在离合飞轮上的离合器，离合器接合后带动其旋转的摩擦盘，与摩擦盘固定在一起、由电机驱动的电动飞轮，固定在电动飞轮上的螺杆，安装在螺杆下部、带 有 内螺纹 的 滑 块。 yiyou-qd.com | J58-6300 clutch type electric drive screw press includes framework, drive motor installed on the top of framework, clutch flywheel driven by drive motor, clutch fixed on the clutch flywheel, friction disc revolved after clutch engagement, electric flywheel fastened with friction disc and driven by [...] electric motor, screw fastened on the electric flywheel, and [...] slide block with internal thread installed under the screw. yiyou-qd.com |
钢管产品：大口径输油管、输气管、无缝钢管、焊管、不锈钢钢管（方管、圆管、异型管）、锥型无缝钢管、无缝异型钢管、工业焊接管、金属波纹管、碳钢管等配件、冷轧无缝管 、 内螺纹 无 缝 钢管、冷拔无缝钢管、锅炉管、防腐蚀特种钢管、合金管、轴承管等、建筑钢管、复合管、复合钢管、导线管、螺纹钢管焊接钢管、热镀锌钢管、电镀锌钢管、洁净管、KBG线路导管、供水管等。 cnyunding.com | Cone seamless steel tubes, abnormal seamless steel pipes and industrial welded pipe, corrugated metal pipe, steel pipes and other accessories, cold-rolled seamless tube, Rifled seamless steel tubes, drawing seamless steel pipe, boiler tube, pipe corrosion special alloy tube, bearings, etc., construction pipes Composite Pipes, composite pipe, wire tube, pipe welding steel pipe, hot galvanized steel pipes, galvanized steel pipes and pipe cleaner. en.cnyunding.com |
英汉双解词典包含2273206条英汉词条，基本涵盖了全部常用单词的翻译及用法，是英语学习的有利工具。