by measurement

The accuracy of the system is not affected by measurement errors, and is unaffected by the range to the aircraft.

INSPECTION BY MEASUREMENT OF THE PROPORTION OF NON CONFORMING ITEMS. GUIDANCE ON THE DESIGN OF A SAMPLING PROGRAMME.

Insulating liquids. Determination of the dielectric dissipation factor by measurement of the conductance and capacitance. Test method.

Welding consumables - Determination of moisture resistance of manual metal arc welding electrodes by measurement of diffusible hydrogen.

As the electronic computer control by measurement precision of packaging, precision greatly.

Objective To investigate the osteoporosis-trauma relationship by measurement of osseous density in patients with bone fracture.

textiles . tests on fibres . determination of length and length distribution by measurement of single fibres.

The structure of target compound and its intermediates were confirmed by measurement of melt-point, IR and elementary analysis.

The example shows that the estimation results are mainly affected by measurement noises when the data resolution is high.

Note that the recommended source resistance varies by measurement range because the RF value also depends on the measurement range.

One C band ultra-low oscillator was produced, and validity of theory and design method was proved by measurement.

The mechanism of growth in Shao duck was investigated by measurement of hormones relative to growth.

Addresses what percent of the tolerance is taken up by measurement error ?

Ceramic tiles. Part 5 : determination of impact resistance by measurement of coefficient of restitution.

was explained by measurement of ESR signal and polarographic half wave potential.

described was the principle of such determination by measurement of pressure difference;

Test Method for Measurement of Thickness of Metallic Coatings by Measurement of Cross Section with a Scanning Electron Microscope

insulating liquids - determination of dielectric dissipation factor by measurement of the conductance and capacitance - test method

Anodizing of aluminium and its alloys; Assessment of quality of sealed anodic oxide coatings by measurement of admittance or impedance

Rubber, vulcanized; Determination of ageing characteristics by measurement of stress at a given elongation

Standard Test Methods for Oxygen Precipitation Characterization of Silicon Wafers by Measurement of Interstitial Oxygen Reduction

Test method for carbon concentration of semi-insulating monocrystal gallium arsenide by measurement infrared absorption method

Aluminium and aluminium alloys - Anodizing - Assessment of quality of sealed anodic oxidation coatings by measurement of admittance

Methods of test for paints - Determination of Knoop hardness by measurement of the indentation length using a microscope

Adhesives - Wettability - Determination by measurement of contact angle and critical surface tension of solid surface

Water quality - Determination of anionic surfactants by measurement of the methylene blue index MBAS

Hydrochloric acid for industrial use; Evaluation of hydrochloric acid concentration by measurement of density

Standard test methods for minority carrier lifetime in bulk germanium and silicon by measurement of photoconductivity decay

Extraction of the Parameters of Laser Rate Equation by Measurement and Dynamic Character Experiment

Inspection: conformity evaluation by observation andjudgment accompanied AS appropriate by meASurement, testing or gauging

Textiles fibres - Determination of length and length distribution of staple fibres (by measurement of single fibres)

Nitric acid for industrial use; Evaluation of the nitric acid concentration by measurement of density

Ceramic tiles - Determination of impact resistance by measurement of coefficient of restitution

Methods of test for paints - Determination of Knoop hardness by measurement of the indentation depth

Anodizing of aluminium and aluminium alloys--Insulation check by measurement of breakdown potential

Test Methods for Minority-Carrier Lifetime in Bulk Geranium and Silicon by Measurement of Photoconductivity Decay

Anodizing of aluminium and its alloys--Assessment of sealing quality by measurement of the loss of mass after immersion in acid solution

Sulphuric acid for industrial use; Evaluation of sulphuric acid concentration by measurement of density

Aluminium and aluminium alloys - Anodizing - Part 5: Assessment of quality of sealed anodic oxidation coatings by measurement of admittance

Paints and varnishes - Determination of micro-indentation hardness - Part 2: Knoop hardness by measurement of indentation depth under load

Paints and varnishes - Determination of micro-indentation hardness - Part 1: Knoop hardness by measurement of indentation length

Estimation of stature and avoirdupois by measurement of fingerprints and footprints

Influence on Firing Accuracy by Measurement Errors of Meteorological Elements

Standard Test Methods for Water Vapor Content of Electrical Insulating Gases by Measurement of Dew Point

Assessment cerebral blood flow infusion by measurement of lenticulostriate artery in neonates by Doppler ultrasound

Standard Test Method for Water Vapor Content of Gaseous Fuels by Measurement of Dew-Point Temperature

Test methods of ceramic tiles-Part 5: Determination of impact resistance by measurement of coefficient of restitution

Methods of test for finishes for wooden furniture - Assessment of low angle glare by measurement of specular gloss at 85 degrees

Acoustics -- Noise from shooting ranges -- Part 1: Determination of muzzle blast by measurement

Evaluation of hair damage degree by measurement of cupric ion adsorption on hair

Ceramic tiles - Part 5: Determination of impact resistance by measurement of coefficient of restitution; Technical Corrigendum 1

Clinical Study on Type of DLT Selected by Measurement of Bronchial Diameter on CT