网站首页  词典首页

请输入您要查询的英文单词:

 

单词 fatigue strength
释义

fatigue strength

美 
英 
  • na.疲劳强度
  • 网络抗疲劳强度;疲乏强度;疲勞强度
na.
1.
疲劳强度

例句

释义:
1.
Fatigue notch factor K(subscript f) is usually used to express the reduction in fatigue strength of the component notch.
疲劳缺口系数K(下标f)是表征缺口部位疲劳强度降低程度的参量,这一系数在结构抗疲劳设计中经常被使用。
www.ceps.com.tw
2.
First of all, the hot melts made of automated as required, and then, in a defined temperature in fatigue strength Tester (self-made).
首先,把热熔胶按规定制成胶条,然后,在规定温度下在疲劳强度测定仪(自制)上进行测试。
www.bing.com
3.
Reviews the effect of remanent stress on fatigue strength by the concept of average stress and fracture mechanics respectively.
从平均应力和断裂力学的观点评述了残余应力对材料疲劳极限的影响。
dictsearch.appspot.com
4.
On the basis denoted above, calibrating calculation is conducted on its stiffness, static strength, fatigue strength and its stability.
在此基础上,对支架进行了刚度、静强度、疲劳强度和稳定性校核计算。
dictsearch.appspot.com
5.
The reliability design of fatigue strength in designated service life of machine elements is investigated.
本文论述机械产品工作到规定寿命时的疲劳强度可靠性设计方法。
journal.ecust.edu.cn
6.
The entire aircraft can be tested simultaneously to prove static and fatigue strength under various flight and ground load conditions.
整个飞机可以同时进行各种飞行负载和接地负载条件下的静力强度测试和疲劳强度测试。
frponline.com.cn
7.
Common fatigue strength reduction factors to account for such things as surface finish can be found in design handbooks.
共同的疲劳强度降低因素占到表面完成这些事可以在设计手册中。
zhidao.baidu.com
8.
The fatigue strength time-varying model was presented considering the fatigue strength of reinforcement varying with the time.
考虑钢筋疲劳强度随时间变化,提出疲劳强度时变模型。
www.ceps.com.tw
9.
Bending a piece of wire back and forth until it breaks is another example of fatigue strength.
弯曲的一块铁丝网来回,直到休息,是另一个例子疲劳强度。
www.fifl.cn
10.
Gas cylinders. Fatigue strength testing under repeated pressurizing for liquefied or dissolved compressed gases.
气瓶。液化或熔解压缩气体气瓶的反复加压疲劳试验。
www.chinastandard.com.cn
1.
In order to increase the using life of the transmission shaft, the fatigue strength of the shaft must be raised.
为了提高传动主轴之使用寿命,必须设法提高主轴之疲勞强度才可以。
www.ceps.com.tw
2.
Static strength and fatigue strength is calculated and results show that the structure strength meets the requirement.
计算结果表明车体结构强度满足要求。
www.ceps.com.tw
3.
moreover , the influence factors of stress ratio , intermittent time , loading order etc . to fatigue strength were discussed.
另外,本文详细分析了、加载顺序、间歇时间、加工缺陷和安装误差等因素对疲劳强度的影响。
www.ichacha.net
4.
The influence of coating thickness upon the fatigue strength will decrease along with the increase of cycling times.
涂层厚度对疲劳强度的影响随循环次数的增加而减小。
www.ceps.com.tw
5.
By analyzing the force applied on the tubing, the tensile strength and anti-fatigue strength of the tubing are calibrated.
通过对油管的受力分析,校核偏磨油管的抗拉强度和抗疲劳强度。
www.chemyq.com
6.
In view of this, the transitional fatigue strength condition under non-symmetrical circulation is incorrect.
由此可知,当前通用的非对称交变应力的疲劳强度条件是不正确的。
www.ceps.com.tw
7.
The paper establishes the mechanical model of pump barrel and connecting rod of cone valve, and check the strength and fatigue strength.
建立了泵筒及锥形阀连杆的受力模型并对其进行强度和疲劳强度计算;
www.13191.com
8.
Casting defects, especially porosity, will reduce fatigue strength of the crank-shaft.
铸造缺陷,尤其是铸造缩松,降低了曲轴的疲劳强度。
www.chemyq.com
9.
Titanium femoral locking screw could significantly increase its fatigue strength.
若股骨螺丝为钛合金,则疲劳寿命会明显提升。
140.118.33.11:8080
10.
The fatigue strength of hardening and tempering coated specimens were higher than that of normalizing coated specimens.
在正火处理后,涂层试样的疲劳强度大于未涂层试样;
www.ceps.com.tw
1.
Its a new method to increase fatigue strength of welded joints and structure by peening toe of weld with ultrasonic peening equipment.
使用超声波冲击焊趾来提高焊接接头及结构的疲劳强度,是一种国际上刚刚出现的新方法:本文对超声冲击方法的试验装置进行了研究。
dictsearch.appspot.com
2.
And the research about seat safety concentrates on the analysis of static strength, impact strength and fatigue strength.
与安全性相关的研究主要围绕座椅的静强度、冲击强度以及疲劳强度的分析。
www.fabiao.net
3.
also made the crankshaft to be of sufficient bending fatigue strength.
又能使曲轴具有足够的弯曲疲劳强度。
www.juyy.net
4.
This study investigated the relationship between high-cycle fatigue strength of austempered ductile iron (ADI) and cast section size.
本研究的目的是探讨不同断面尺寸对沃斯回火球墨铸铁高周疲劳性质的影响。
www.ncu.edu.tw
5.
The conclusion shows that the design according to the original fatigue strength condition would cause greater losses.
结论指出,按原有的疲劳强度条件进行设计有时会造成较大的浪费。
www.ceps.com.tw
6.
The residual stresses impacts the working performance and fatigue strength of parts.
已加工表面存在的残余应力影响工件的使用性能和疲劳强度。
www.juyy.net
7.
Improving contact load is limited by contact fatigue strength of transmission parts.
提高接触载荷,又受到传动零件接触疲劳强度的限制。
paper.pet2008.cn
8.
High bending fatigue strength and contact fatigue strength are needed for heavy duty gear steels.
重载齿轮钢要求具有高的弯曲疲劳强度和接触疲劳强度。
www.dictall.com
9.
the effect to fatigue strength of crossing bar of freight car due to unbalanced wheelset is analyzed.
分析了提速货车装用不平衡轮对后对交叉杆疲劳强度的影响。
www.juyy.net
10.
Hull structure of container vessel should have adequate shearing strength, buckling strength and fatigue strength.
集装箱船舶的船体结构应具有足够的剪切强度、屈曲强度和疲劳强度等特点。
www.ceps.com.tw
1.
THERMOPLASTICS VALVES. FATIGUE STRENGTH. TEST METHOD. (EUROPEAN STANDARD EN 28659).
热塑料制阀门.耐疲劳强度.试验方法.(欧洲标准EN28659)
www.mapeng.net
2.
At last, the impact of welding quality to the traction seats fatigue strength was studied.
最后,论述了焊接质量对牵引座疲劳强度的影响;
paper.pet2008.cn
3.
the bending fatigue strength of dedendum before and after the modification were checked.
同时对改进前后的齿根弯曲疲劳强度进行了校核。
www.juyy.net
4.
P Prestressing tendons shall have adequate fatigue strength.
钢筋必须有足够的疲劳强度。
gatefanyi.com
5.
Fatigue strength and failure mechanisms are presented.
将介绍疲劳强度及失效机制。
dict.bioon.com
6.
It is generally accepted that fatigue strength is drastically lower if the concrete is cracked.
人们普遍认为,如果混凝土出现裂缝,那么疲劳性能会大大减低。
wenku.baidu.com
7.
Fatigue strength is the property of a material to resist various kinds of rapidly alternating stresses.
疲劳强度是财产的材料,抵制各种压力迅速交替。
www.fifl.cn
8.
P Where fatigue strength is required it shall be verified in accordance with EN 10080.
当对疲劳强度有要求时,必须按照EN10080进行检验。
gatefanyi.com
9.
Carbon steel has high and low temperature strength, is very tough and has excellent fatigue strength.
碳钢具有高温和低温强度,具有很高的韧度和优异的抗疲劳强度。
tr.bab.la
10.
For the of 2000000 cycles, the fatigue strength of the both is almost the same.
在200万次循环下,两者的疲劳强度基本相当。
www.ceps.com.tw
1.
A kind of method to evaluate and test the tension-compression fatigue strength of gray cast iron was introduced in this paper.
介绍了一种评价与测试灰铸铁铸件的拉压疲劳极限的方法。
www.chemyq.com
2.
The second one is on the integral forced performance of stay cable, including both static strength and fatigue strength.
第二部分,斜拉索的整体受力性能,主要包括静力强度和疲劳强度两个内容。
paper.pet2008.cn
3.
The result indicates that the static strength and fatigue strength of bogie frame satisfy the design requirements for UIC615-4.
计算结果表明,新设计构架满足UIC615-4规范对构架强度的要求,构架各部位满足疲劳强度要求。
www.boshuo.net
4.
Of gear foot and contact fatigue strength of gear profile.
齿根弯曲疲劳强度,齿面接触疲劳强度。
www.juyy.net
5.
Furthermore, fatigue strength of welded joints subjected to operating loads has been intensively examined (Refs. 1-12).
此外,焊接接头工作载荷引起的疲劳强度检验也正加紧研究。
www.rjghome.com
6.
The Effect Coefficient of Gear Tooth (ECGT) is an important parameter while the flex spline's fatigue strength is studied.
轮齿影响系数(ECGT)是研究柔轮疲劳寿命时一个非常重要的参数。
www.ceps.com.tw
7.
The hard second phase, for example martensite , contributed to the superior fatigue strength and higher threshold value.
较硬的第二相,如马氏体,贡献了出众的疲劳强度和较高的开始值。
dictsearch.appspot.com
8.
The results showed that the fatigue strength of Low alloy steel in corrosion medium was much lower than that in air.
结果表明:与空气相比,腐蚀介质使低合金钢的疲劳强度显著降低;
lxsj.cstam.org.cn
9.
Discussion on Some Question of Evaluation of Crankshaft Bending Fatigue Strength Test
曲轴弯曲疲劳强度试验评估中若干问题的探讨
ilib.cn
10.
The Statistical Characteristic of Fatigue Strength Estimation Decided by the Up and Down Method
升降法确定的疲劳强度估计量的统计特性
www.ilib.cn
1.
An Application of Finite Element Method on Bending Fatigue Strength Calculation of the Teeth of a Standard Straight Spur Gear
有限元法在标准直齿圆柱齿轮轮齿弯曲疲劳强度计算中的应用
service.ilib.cn
2.
Comparative Study of Improving Fatigue Strength of Blade by Stress Peening and Vibrating Finisher
喷丸与振动光饰提高零件抗疲劳强度的对比
www.ilib.cn
3.
Study of Improvement on Contact Fatigue Strength of Carbonitriding Gears by Shot Peening
强力喷丸对提高碳氮共渗齿轮接触疲劳强度的研究
ilib.cn
4.
obtaining safety coefficient of stress concentration through finite element method calculation on the static and fatigue strength;
进行曲轴的静强度和疲劳强度有限元计算,得出了应力集中部位的安全系数;
www.lw23.com
5.
Experiment Life Evaluation and Fatigue Strength Analysis on Alter-Rigidity Spring Combinations of New Type Freight Car Bogie
新型货车转向架变刚度弹簧组的试验寿命估算及疲劳强度分析
www.ilib.cn
6.
Research of the Fatigue Strength Evaluation Result Effected by the Measuring Data Quantities
实测数据量大小对疲劳强度评估结果影响的研究
www.ilib.cn
7.
Study of Fatigue Strength Condition for Non-Symmetrical Circulation
非对称交变应力下疲劳强度条件的探讨
www.ilib.cn
8.
A Study of Project Method for Load Bearing Structure Fatigue Strength in High-Speed Power Vehicle
高速动力车承载结构疲劳强度分析的工程方法研究
service.ilib.cn
9.
The Impact of Friction on Contact Stress and Fatigue Strength of the Eccentric Wheel Handspike Planetary Transmission
摩擦对偏心轮推杆行星传动接触应力及疲劳强度的影响
service.ilib.cn
10.
Three-dimensional stress concentration and its influence on the fatigue strength at an elliptic hole
椭圆孔三维应力集中及其对疲劳强度的影响
www.ilib.cn
1.
The effect of the friction between teeth on the contact fatigue strength of the tooth surfaces of a gearing
齿间摩擦对齿轮轮齿表面接触疲劳强度的影向
ilib.cn
2.
Research of Applying Evolutionary Algorithm to Survey Planning of Fatigue Strength Deteriorating of Bulk Carrier Hull Structure
基于进化算法的散货船结构疲劳破损检验计划研究
www.ilib.cn
3.
The residual stress and its influence on the fatigue strength induced by explosive autofrettage
爆炸自紧残余应力及对构件疲劳强度的影响
www.ilib.cn
4.
Influence of bolt fatigue strength of the structure form of nut
螺母外形结构对螺栓疲劳强度的影响
service.ilib.cn
5.
Up and Down Method for Fatigue Strength with two Details in Series
测定疲劳强度的双细节串联升降法
scholar.ilib.cn
6.
Fatigue strength measurement and comparative fatigue characteristics of ductile iron
球墨铸铁疲劳强度测试及疲劳性能对比
www.ilib.cn
7.
Calculation of the bending fatigue strength at the tooth root of driving gears on reduction gear drives
减速齿轮传动中主动轮齿根弯曲疲劳的计算
www.ilib.cn
8.
Ultrasonic peening improves the fatigue strength of welded joints in a ultra-fine grained steel
超声捶击提高超细晶粒钢焊接接头的疲劳性能
www.ilib.cn
9.
The Fatigue Strength Evaluation System for the Crane Main Girder Structure in the Metallurgical Industry
冶金行业用起重机主梁结构疲劳强度评估方法
www.ilib.cn
10.
Correction on number of times method of equivalent cycle in the theory of fatigue strength
对疲劳强度理论中的等效循环次数法的修正
service.ilib.cn
1.
Calculation on touched fatigue strength of the gear's nodes beyond the intermeshing area
节点位于啮合区外的齿轮接触疲劳强度计算
www.ilib.cn
2.
Fatigue strength tests and study of main girders of metallurgy cranes
冶金起重机主梁疲劳强度的试验与研究
service.ilib.cn
3.
Summarization about Fatigue Strength Research of Submarine Structures
潜艇结构疲劳强度研究综述
www.ilib.cn
4.
Studies on Application of Deep Rolling Depression Technology to Improve Fatigue Strength of Crankshafts
用深滚压技术提高曲轴疲劳强度的应用研究
ilib.cn
5.
Fatigue Strength Analysis and Structural Optimization of a Crankshaft Based on Finite Element Method
基于有限元法的曲轴结构分析及优化
service.ilib.cn
6.
Analysis and Study of Influence to Fatigue Strength of Weld Structure by Rib
肋板对焊接结构疲劳强度影响的分析研究
service.ilib.cn
7.
Analysis on the fracture cause and fatigue strength calibration calculation of bolts in hydrogen compressor
氢压机螺栓断裂分析及疲劳强度核算
ilib.cn
8.
Improving the Fatigue Strength of Welded Joints by Low Transformation Temperature Electrodes
利用低相变点焊条改善焊接接头的疲劳强度
www.ilib.cn
9.
Influence of design parameters of mixture ratio on corrosion fatigue strength of high performance concrete
配合比设计参数对高性能混凝土腐蚀疲劳强度的影响
ilib.cn
10.
Standard Test Methods for Determination of Static and Cyclic Fatigue Strength of Ceramic Modular Femoral Heads
测定陶瓷模股骨头部静态和轮转的疲劳强度的测试方法
www.std168.com
1.
Fatigue Strength of Welded Joints for Architecture Reinforcement Steel Bar With Ultrafine Grains
超细晶粒钢筋焊接接头的疲劳强度
www.ilib.cn
2.
Crossing Bar Fatigue Strength Effect Analysis of Raising Speed Freight Car with Unbalanced Wheelset
提速货车装用不平衡轮对后对交叉杆疲劳强度影响的分析
www.ilib.cn
3.
Research of Stress Field Intensity Model on the Fatigue Strength Prediction for Welded Steel Structures
焊接钢结构疲劳强度预测的应力场强模型研究
ilib.cn
4.
A fatigue strength design criterion of thick cylinders subjected to repeated internal pressure
一种受循环内压厚壁圆筒的疲劳强度设计准则
www.ilib.cn
5.
Effect of Nickel Electrodeposit Thickness Obtained from Multi-wave Current Plating on Lead Fatigue Strength
多波形电流镀镍层厚度对引线疲劳强度的影响
www.ilib.cn
6.
Research into the Material and Fatigue Strength of Connecting Rod for High- speed Diesel Engine
高速柴油机连杆的材料与疲劳性能研究
ilib.cn
7.
Effects of Grinding, Lapping and Cloud Bursting on Martensitic Stainless Steel's Fatigue Strength
磨削、研磨、喷丸处理对马氏体不锈钢疲劳强度的影响
service.ilib.cn
8.
Computer simulation of the fatigue strength of cruciform welded joints
十字型焊接接头疲劳强度的计算机模拟
www.ilib.cn
9.
Calculation of the fatigue strength of the member under unsymmetric cycles
不对称循环下构件的疲劳强度计算
wenku.baidu.com
10.
An Investigation on Random Fatigue Strength of K-Type Tubular Joints and Crack Propagation Behaviors
K型管状接头随机疲劳强度和裂纹扩展规律的研究
www.ilib.cn
1.
An Investigation on Random Fatigue Strength of K-Type Tubular Joints and Crack Propagation Behaviors
K型管状接头随机疲劳强度和裂纹扩展规律的研究
www.ilib.cn
2.
The design of fatigue strength fuzziness probability for the cylinder of plunger pump
柱塞泵缸体疲劳强度的模糊概率设计
www.ilib.cn
3.
Bayes Analysis of Fatigue Strength Distribution Parameters
疲劳强度分布参数的贝叶斯分析
www.ilib.cn
4.
Reliability analysis of bending fatigue strength for micro-segments helical Gear
斜齿微线段齿轮弯曲强度可靠性研究
ilib.cn
5.
Reliability Analysis of Diesel Engine Connecting Rod Fatigue Strength
柴油机连杆杆身疲劳强度可靠性分析
ilib.cn
6.
The calculation for the bending fatigue strength of tooth roots for marine gearings
船用齿轮齿根弯曲疲劳强度计算
www.ilib.cn
7.
Fatigue strength under pulsating compression stress
脉冲压应力疲劳强度
www.dic123.com
8.
Fatigue Strength Optimum Design of Multi-Layer Press-Fit Composite Cold Extrusion Concave Die
多层压配组合冷挤压凹模疲劳强度优化设计
www.ilib.cn
9.
Fuzzy comparison on the discount coefficient of concrete fatigue strength
混凝土疲劳强度折减系数的模糊比较
service.ilib.cn
10.
Orthogonal analysis on fatigue strength of laser coating under repeated impact load
激光涂层多冲碰撞疲劳强度的正交分析
service.ilib.cn
1.
Influence of Training with Secondary Load on Bending Fatigue Strength of Crankshaft
次载锻炼对曲轴弯曲疲劳强度的影响
ilib.cn
2.
The Effects of Material Grade to the Bending Fatigue Strength of Ductile Iron Crankshaft
材料牌号对球铁曲轴弯曲疲劳强度的影响
www.ilib.cn
3.
Investigation for Matrix on Hot Fatigue Strength of Vermiculate Graphite Cast Iron
基体组织对蠕墨铸铁热疲劳性能的影响
www.ilib.cn
4.
Direct calculation for fatigue strength analysis of ship structures
船体结构疲劳强度分析直接计算法
service.ilib.cn
5.
A simplified check the fatigue strength of turning axle in a stable state
稳定状态下转轴疲劳强度的简化校核
www.ilib.cn
6.
Fuzzy Reliability Design of Bridge Fatigue Strength and Fatigue Life Analysis
桥梁疲劳强度的模糊可靠性设计与疲劳寿命分析
www.ilib.cn
7.
Technical Measures to Improve Fatigue Strength of Press Oscillating Axle
提高压力机摇摆轴疲劳强度的技术措施
ilib.cn
8.
Research for enhancing the contacting fatigue strength of cast iron gears with Ni-P and Ni-Co alloy coating
表面镍磷、镍钴合金镀层提高铸铁齿轮接触疲劳强度研究
service.ilib.cn
9.
The fatigue strength analysis of the rotor of defective generator
带缺陷发电机转子疲劳强度分析
ilib.cn
10.
The Test and Investigation on the Tension- compression Fatigue Strength of Gray Cast Iron
灰铸铁拉压疲劳极限的试验研究
www.ilib.cn
1.
New Method for Calculating Fatigue Strength Reliability
一种新的疲劳强度可靠性计算方法
service.ilib.cn
2.
Fatigue strength under completely repeated stress
全反复脉冲应力疲劳强度
www.dic123.com
3.
Study on Local Approach of Fatigue Strength Prediction for Welded Structures
焊接结构疲劳强度预测的局部法研究
service.ilib.cn
4.
Application of Gray System Theory in Predicting Fatigue Strength of Concrete
灰色理论在混凝土疲劳强度预测中的应用
www.ilib.cn
5.
Evaluation on Fatigue Strength of Duplex Stainless Steel Welded Joints by Hot Spot Stress
用热点应力评定双相不锈钢焊接接头疲劳强度
www.ilib.cn
6.
The reliable design to fatigue strength of hollow axle combined with bolt in simple ball grinder
球磨机筒体中空轴处连接螺栓疲劳强度的可靠性设计
www.ilib.cn
7.
Stress Analysis of Bearing Metal and Research of Testing Method for Fatigue Strength
合金轴瓦的应力分析与疲劳实验方法
ilib.cn
8.
The fatigue strength of new type of bracket joints with curved web in bulk carrier
散货船新型曲边肘板节点的疲劳强度
ilib.cn
9.
Effects of Machining on Fatigue Strength under Reversed Bending Stress
机械加工对弯曲疲劳强度的影响
www.ilib.cn
10.
oil tanker; hot spot stress; fatigue strength; finite element analysis
油船;热点应力;疲劳强度;有限元;
www.airitilibrary.com
1.
Contact fatigue strength involving the effects of shipbody deformation and friction between teeth
计入船体变形及齿间摩擦的齿面接触疲劳强度
service.ilib.cn
2.
Quantitative Analysis of the Effect of Surface Topography on Fatigue Strength
表面微观形貌对疲劳强度影响的定量分析
www.ilib.cn
3.
Effect of TIG weld toe remelting techniques on the improvement of fatigue strength of T-shaped joints
焊趾TIG重熔工艺对改善T型接头疲劳强度的影响
www.ilib.cn
4.
Effect of Heat Treatment on the Fatigue Strength of Vacuum Melted Ni Based Alloy-WC Composite Coating
热处理对镍基合金碳化钨硬面涂层疲劳强度的影响
service.ilib.cn
5.
Frame Fatigue Strength Test and Test Equipment for Two-wheeled Motorcycles
两轮摩托车车架疲劳强度试验及试验设备
www.ilib.cn
6.
Experiment of Fatigue Strength for Sliding Bearing Material
滑动轴承材料疲劳强度试验
ilib.cn
7.
Improvement of Fatigue Strength of High Strength Aerospace Fastener by Using Rolling
滚压加工技术提高高强航空紧固件的疲劳强度
www.ilib.cn
8.
Fuzzy Synthesis Analysis on Weld Fatigue Strength of Pressure Vessels
压力容器焊缝疲劳强度模糊综合分析
www.ilib.cn
9.
Measures on improving the fatigue strength of machine components
提高机械零件抗疲劳强度的措施
www.ilib.cn
10.
Reliability Analysis of Contact Fatigue Strength of Cycloid Gear in FA Reducer
FA传动摆线轮齿面接触疲劳强度可靠性分析
www.ilib.cn
1.
Effect of Different Anodizing Processes on the Fatigue Strength of Aluminum Parts
不同阳极氧化工艺对铝制件疲劳强度的影响
www.ilib.cn
2.
Research on Fatigue Strength Reliability for the Cycloid Ball Planetary Transmission Based on Fuzzy Theory
基于模糊理论的摆线钢球行星传动接触疲劳强度可靠性研究
ilib.cn
3.
Research on Fatigue Strength for Steel Girder Details of Wuhu Yangtze River Bridge
芜湖长江大桥钢梁细节疲劳强度的研究
ilib.cn
4.
Effect of Heat-treatment on the Fatigue Strength of Vacuum Melted Ni base alloy-WC Composite Coating
热处理对镍基合金-碳化钨复合涂层组织的影响
www.ilib.cn
5.
A Research on the Contact Fatigue Strength of Alloy Cast Iron Gear Drives with Alloy Coating
涂镀合金层的合金铸铁齿轮的接触疲劳强度研究
168.160.184.82:8080
6.
Effect of Prior Austenite Grain Size on Fatigue Strength in High Si Oil-tempered Wire for Valve Springs
奥氏体晶粒度对高Si油回火钢丝疲劳强度的影响
www.ilib.cn
7.
Analysis on the Dynamic Fatigue Strength of Diesel Engine Crankshaft
柴油机曲轴动态疲劳强度分析
www.ilib.cn
8.
Fatigue strength for alternating tensile stress
交变拉应力疲劳强度
www.dic123.com
9.
Pulsating fatigue strength under bending stress
脉动抗弯疲劳强度
www.dic123.com
10.
Reliability analysis of bending fatigue strength for double arc gear
双圆弧齿轮传动弯曲疲劳强度可靠性分析
www.ilib.cn
1.
Fatigue Strength of Ni Base Alloy-Chromium Carbide Composite Coating
镍基-碳化铬硬面复合涂层的疲劳强度
www.ilib.cn
2.
The Fuzzy Reliability Design of Fatigue Strength For Bolt Connection
螺栓联接疲劳强度的模糊可靠性设计
www.ilib.cn
3.
Fatigue Strength Assessment of Large-scale Ship Structures
大型船舶结构的疲劳强度校核方法
scholar.ilib.cn
4.
Influence of Interference-Fit Riveting on Fatigue Strength
干涉配合铆接对疲劳强度的影响
service.ilib.cn
5.
Study on bending fatigue strength of automobile steering bridge
汽车转向桥弯曲疲劳强度研究
www.ilib.cn
6.
Torsion Fatigue Strength Test for Nodular Cast Iron Crankshaft of Engine
发动机球铁曲轴扭转疲劳强度的试验研究
ilib.cn
7.
Study on Ginseng Increasing Mouse Ability of Sports and Fatigue Strength
中药人参对提高大鼠运动能力及抗疲劳的实验研究
service.ilib.cn
8.
Fuzzy reliability design of fatigue strength of V-belt transmission
V带传动疲劳强度的模糊可靠性评价
www.ilib.cn
9.
Fatigue strength under reversed bending stress
反复弯曲应力疲劳强度
www.dic123.com
10.
Fatigue strength and fatigue fracture analysis of tubing of rod-pumped well
抽油机井油管的疲劳强度及其疲劳断裂分析
www.ilib.cn
1.
Effect of Process Conditions on Fatigue Strength of Leads for Metallic Package
工艺因素对金属封装外引线弯曲疲劳的影响
service.ilib.cn
2.
Fatigue strength checking method for hull structure
船体结构疲劳强度的检验
www.ilib.cn
3.
Value Reliability Analysis for Rod Fatigue Strength
抽油杆疲劳强度价值可靠性分析
www.ilib.cn
4.
Experimental Study on the Effect of Environmental Change to Fatigue Strength of Improving Soil
环境变化对改良土疲劳强度影响的试验研究
www.ilib.cn
5.
The Fatigue Strength Analysis of Connecting Rod of Diesel Engine Using FEM
柴油机连杆的有限元疲劳强度分析
ilib.cn
6.
Several Methods to Improve the Fatigue Strength of Turbine Blades
提高涡轮叶片疲劳强度的几种措施
service.ilib.cn
7.
Fillet rolling schemes and the fatigue strength of engine crankshaft
曲轴的圆角滚压工艺与疲劳强度
www.ilib.cn
8.
Fatigue strength analysis of the forge press frame
油压快锻机机架疲劳强度分析
ilib.cn
9.
Survey of Fatigue Strength Theory of Turbine Rotor
汽轮机转子疲劳强度理论研究现状与展望
service.ilib.cn
10.
Calculation and analysis of fatigue strength of drill string in deep well
深井钻柱疲劳强度计算与分析
ilib.cn
1.
A study into fatigue strength of laser welds of pure titanium and titanium alloy
激光焊接钛试件疲劳强度的研究
www.ilib.cn
2.
Fatigue strength of duplex stainless steel welded joint
双相不锈钢焊接接头疲劳强度
www.ilib.cn
3.
Analysis on the Air Suspension Structure Based on Fatigue Strength Method
基于疲劳理论的汽车空气悬架结构件的弯曲强度计算
service.ilib.cn
4.
FEM Analysis on Fatigue Strength of Diesel Engine Connecting-Rod
发动机连杆疲劳强度有限元分析
www.ilib.cn
5.
Analysis on Fatigue Strength of Nodular Cast Iron Connecting Rod in Engi
发动机球墨铸铁连杆疲劳强度分析
ilib.cn
6.
Fatigue Strength of Hard Coating in Different Stress States
不同应力状态下硬面涂层材料的疲劳强度
service.ilib.cn
7.
The fuzzy reliability design of fatigue strength for criindrical helical spring
圆柱螺旋弹簧疲劳强度的模糊概率设计
www.ilib.cn
8.
Investigation on Bending Fatigue Strength of ADI Gears
奥贝球铁齿轮弯曲疲劳强度的试验研究
168.160.184.82:8080
9.
Fatigue Strength of Bogie Frame of High-Speed Train under Spectrum Load
基于谱载荷的高速列车转向架的疲劳强度
scholar.ilib.cn
10.
Prediction of Fatigue Strength for the T-Type Welded Joint
丁字形焊接接头疲劳强度的预测
www.ilib.cn
1.
Influences of Heat Treating Process on Bending Fatigue Strength of Carburized Gears
热处理工艺对渗碳淬火钢齿轮弯曲疲劳强度的影响
ilib.cn
2.
Fatigue Strength of Graphite-Matrix Interface in Austempered Ductile Iron
奥氏体-贝氏体球墨铸铁中石墨与基体界面的疲劳强度
www.ilib.cn
3.
Contact fatigue strength comparison of laser-hardened gear and carburized gear
激光淬火齿轮与渗碳淬火齿轮的接触疲劳强度对比实验研究
service.ilib.cn
4.
The search of calculating method of contact fatigue strength for gear
齿轮接触疲劳强度计算方法的探讨
www.ilib.cn
5.
Calculation Based on Friction between Teeth on Contract Fatigue Strength of Helical Gear Tooth Surfaces
基于摩擦的斜齿轮齿面接触疲劳强度计算
www.ilib.cn
6.
Effective method of improving fatigue strength of rail bolts
提高钢轨螺栓疲劳强度的有效方法
service.ilib.cn
7.
Fatigue Strength Evaluation of Welded Frame
焊接构架疲劳强度的评估方法
www.ilib.cn
8.
Progress in fatigue strength of metal prosthesis
金属修复体疲劳强度的研究进展
www.scirss.com
9.
Calculation of Gear Tooth Root Flexural Fatigue Strength under the Action of Friction
摩擦力作用下的齿轮齿根弯曲疲劳强度的计算
www.ilib.cn
10.
Talking about the fatigue strength design in electronic scale
谈谈电子秤中的疲劳强度设计
www.ilib.cn
1.
Fatigue strength for percent survival
疲劳强度存活率
www.dic123.com
2.
Calculation model of concrete fatigue strength based on fuzzy reliability analysis
基于模糊理论的混凝土疲劳强度计算模型
service.ilib.cn
3.
Improving the Fatigue Strength of Welding Joint
提高焊接接头疲劳强度途径的探讨
www.ilib.cn
4.
Fatigue strength of welded joints of high strength steel
高强度钢焊接接头疲劳强度
www.ilib.cn
5.
Fatigue Strength Analysis for Different Structure of Crankshaft
不同结构曲轴的疲劳强度分析
www.ilib.cn
6.
Study on the fatigue strength of driver occupation
汽车驾驶员职业性疲劳的研究
www.ilib.cn
7.
Contact fatigue strength of marine gear tooth face
船用齿轮齿面接触疲劳强度的研究
www.wenloo.com
8.
Thermal Fatigue Strength on Marine Engine's Piston
船舶柴油机活塞的热疲劳强度分析
ilib.cn
9.
The influence of heat treatment on fatigue strength of 50 steel in the very high cycle regime
热处理工艺对50钢超高周疲劳性能的影响
www.ilib.cn
10.
Study on Hi-cycle Fretting Fatigue Strength of Iron
铁的高周摩擦疲劳强度试验研究
www.ilib.cn
1.
Splice fatigue strength of steel wire core belt
钢绳芯输送带的接头疲劳强度
ilib.cn
2.
Influence of Mean Stress on Fatigue Strength of 50 Steel in Super High Cycle Regime
平均应力对50钢超高周疲劳性能的影响
www.ilib.cn
3.
Fatigue Strength Analysis of Oil Tube
油管的疲劳强度分析
www.ilib.cn
4.
Fatigue Strength Test of a Kind of Piston Pin
活塞销的疲劳强度考核试验
www.ilib.cn
5.
Fatigue strength for finite life
有限寿命疲劳强度
www.dic123.com
6.
Details of welding structure design based on fatigue strength
基于疲劳强度的焊接结构设计细节
ilib.com.cn
7.
Investigation on fatigue strength and design of hinge sleeve based on FEM
基于有限元法的铰链梁疲劳强度分析与设计研究
www.ilib.cn
8.
A Study on Contact Fatigue Strength of ADI
奥贝球铁材料接触疲劳强度的研究
www.ilib.cn
9.
The Study on the Influencing Factor for Fatigue Strength of Crankshaft in Diesel Engine
柴油机曲轴疲劳强度影响因素研究分析
www.ilib.cn
10.
Structural fatigue strength in crane design rules in China
我国起重机设计规范中的结构疲劳强度计算
www.ilib.cn
1.
Research on the Fatigue Strength of Weld Joint and the Improvement of Technique and Technology
焊接接头疲劳强度的研究及其技术工艺的改进
www.ilib.cn
随便看

 

英汉双解词典包含2704715条英汉词条,基本涵盖了全部常用单词的翻译及用法,是英语学习的有利工具。

 

Copyright © 2004-2022 Newdu.com All Rights Reserved
更新时间:2024/12/25 15:17:41