网站首页  词典首页

请输入您要查询的英文单词:

 

单词 ejector pin
释义

ejector pin

美 
英 
  • na.退件销
  • 网络顶针;顶出销;顶杆
na.
1.
顶杆,顶出销,退件销

例句

释义:
1.
The gate location, ejector pin location and parting line (especially cosmetic surface) must be approved by US before tooling .
入水、顶针位置以及分型线(特别是外表面)等在加工前必须得到美国确认。
wenku.baidu.com
2.
the fiber ejector pin adjusting mechanism is of manual mode or electric mode.
光纤顶杆调节机构为手动方式或电动方式。
ip.com
3.
All gates and ejector pin locations shall be approved by igt hardware engineering department paior to tool construction.
所有的大门和顶针位置应经糖耐量paior工具建筑五金工程部。
wenwen.soso.com
4.
NO EJECTOR PIN MARK, GATE FLASH, SCRATCHES OR IMPERFECTIONS PERMISSIBLE ON SURFACE INDICATED.
在指定的表面上不允许有顶针痕迹,水口,刮痕或者压痕。
wenku.baidu.com
5.
2 gate, vents parting line, and ejector pin locations must be approved by XXX prior to die construction.
浇注前,浇道、排气道以及起模杆的铺设位置必须经过XXX的批准。
www.jxzsk.com
6.
The vent system composed of vent groove, vent plug and clearance of ejector pin can fit the need of venting.
采用分型面排气槽、顶杆间隙排气与排气塞排气相结合的排气系统设计能够很好地满足模具排气需要。
www.chemyq.com
7.
The undercut area may stick slide. We may consider to add an ejector pin on the slide.
产品扣位处可能粘行位。我们需考虑行位上加顶针;
www.wzwang.com
8.
Clearance of ejector pin is used to vent little quantity air or the part may intervene with vent plug and ejector pin.
推杆间隙排气用于排气量不大或者开设排气塞会与推出机构产生干涉的部位。
www.chemyq.com
9.
Restricted by the structure of the part, so the ejector pin should be thin and long, and it is also very important to check its intensity.
由于受塑件结构的限制,所以推杆的设计应该比较长但直径不宜太大,而且推杆的强度校核也十分重要。
www.docin.com
10.
It is assumed that an ejector pin is a column that is fr~ at the loaded end and clamped at the other end, as illustrated in Fig. 15.
据推测,一个顶针,是一列是在神父?装载结束,在另一端夹紧,如图所示。15。
women.zhishi.sohu.com
1.
Determination of the Diameter of the Ejector Pin in the Design of the Cavity Mould
型腔模设计中推杆直径的确定
ilib.cn
2.
Design of Thin Slanted Ejector Pin Demoulding of the Mould for Cell Phone
手机模具小斜推杆脱模新设计
ilib.cn
3.
a resetting spring of the ejector pin is exchanged;
更换该顶杆的一复归弹簧;
ip.com
4.
ejector pin with cylindrical head
带肩推杆
blog.sina.com.cn
5.
die - casting die components - part 16 : flat ejector pin
压铸模零件第16部分:扁推杆
www.ichacha.net
随便看

 

英汉双解词典包含2704715条英汉词条,基本涵盖了全部常用单词的翻译及用法,是英语学习的有利工具。

 

Copyright © 2004-2022 Newdu.com All Rights Reserved
更新时间:2025/8/2 17:14:25