deg.C

The low temperature refrigerator features that it has at least one of its compartments in the temperature not higher than -40 deg. c.

The newly resurfaced black, black track soaked up the heat rays and its temperature rocketed to more than 60-deg C.

designs the pipeline drier at set temperature of 800 deg. C, making the surface bond between nickel and iron belt large.

the surface temperature of the blade of the cutting knife is maintained lower than 40 DEG C.

The report said unless nations slash carbon emissions, the world would warm by an average 2 deg C in less than 40 years.

and cooling the distillate to 0 deg. c and filtering off the separated matter to obtain liquid methyl ester or biological diesel oil.

The device can be automatically started to implement temperature reduction when the temperature of the silicon chip reaches 50 DEG C.

The rubber composition is freeze protected for temperature as low as -35 DEG C. and may be used as a tire sealant, among other uses.

With a cooling tower using said nozzle, the temp can drop as large as 9 deg. c by once atomization.

He developed flu-like symptoms with a temperature of39. 4 deg C, generalised malaise, headache and anorexia.

heating at 35 DEG C and stirring to volatilize solvent to prepare polyester microsphere with uniform and monodisperse size.

a thin film of micro porous polyurethane film is bonded on the exposed area of PU foam by a process of hot lamination at 160 DEG C.

Cool the building at 24 deg, C when it is occupied and stop cooling when it is not occupied.

The new electrolyte allows for the electrolytical reduction of alumina at temperatures as low as 700 DEG C.

The luminescent layer (17) further comprises inorganic softening particles (27) with a softening point above 450 DEG C.

The particular advantage of this coating is that the binder can already be completely hardened at below 400 DEG C.

and a step in which the mixture is cooled to 120 DEG C or lower.

Meanwhile, the permanent magnet is subjected to aging at 130 DEG C and surface blue-white zinc plating treatment.

This invention discloses a process for deeply deodorizing kerosene distillation (distilling at 150-270 deg. C) while making it fragrant.

the bulk alloy obtained is packaged in a quartz tube for heat treatment in the temperature of 800 to 950 DEG C and cooled in air.

In certain embodiments the substrate is heated to a temperature between about 1030 DEG C and 1050 DEG C.

leading gas containing oxygen into the reaction chamber and heating to 700-1100 DEG C to grow the zinc aluminate nano-material.

bailing, drying and putting into the 150 deg. c baking machine to generate product.

an finally stirring the matrix asphalts and the mixture at 115-135 DEG C and cooling to obtain the modified asphalt regeneration agent.

The present invention can produce fired brick through firing below 1100 deg. c or produce unburned brick.

and finally, stirring the matrix asphalt and the mixture at 115-135 DEG C and cooling to obtain the plain asphalt reclaiming agent.

The main symptoms are a sudden high fever of over 38 deg C.

if the processing time is pretty short, the moderate etching condition could be obtained at the temperature higher than 40 deg C.

It is produced through adding lycopene and carotene into sesame oil, stirring at 50-60 deg. c for dissolving, homogenizing and packing.

Heat olive oil in pan at 80 deg C. Fry the salmon fillet for 15 mins till cooked. Season with salt and pepper, then place aside.

and burning the residue yielded in the hydrolyzing step at a temperature of 400 to 1200 DEG C.

From the latter solution, crystals of Cefditoren pivoxyl are induced to deposit by addition of water at a temperature of 0 - 10 DEG C.

and (5) the drying process: drying separated materials at 50-150 DEG C to obtain the nano catalytic composite materials.

and introducing carbon source gas to the heating furnace, growing the carbon nano tube within a period of time in 400 DEG C to 800 DEG C.

Please check whether the environment of high temperature over 40 DEG C, such as more than just improve.

and finally drying and smashing the sorbent at the temperature of 30 to 60 DEG C.

and vibrating stoving at 80-95 deg. c to obtain nanometer level carbon black.

Heat the mixture to 55 deg C (131 deg F) and maintain for the whole reaction.

Please mix with boiled water below 50 deg. c.

Said ink composition can prevent the thermally inclused phase separation before 60 deg. C before about 70 deg.

delivering a screened and carded fiber in a primary state into a hot-blast fiber drying machine at 80-100 DEG C by a pipeline to be dried;

applying a release agent in a mould used for preparing polyurethane, and maintaining the temperature of the mould at 45-48 DEG C;

placing the copper substrate after polishing treatment in a heating furnace, filling protective gas to be heated to 400 DEG C to 800 DEG C;

installing the metal die on a mechanical device with heat source supply and controlling the temperature of the metal die below 85 DEG C;

carrying out filtration on the solution of ion exchange reaction at room temperature, collecting filtered materials and drying at 80 DEG C;

secondly, extrusion reaction is performed on water and mixture together at a temperature of between 140 and 160 DEG C;

The utility model can be used at the temperature of about 500 DEG C, and can avoid waste of heat energy and secondary pollution;

Specification for Synthetic Rubber Heat- and Moisture-Resisting Insulation for Wire and Cable, 75 Deg C Operation

heating to 50 deg. c, adding partial formaldehyde to synthesize boron-containing linear phenolic resin;

the step of drying: removing water gas by utilizing the temperature of more than 50 DEG C to obtain a dry polymer;

a heating step comprising concentration of the mother liquor obtained in step (3) followed by a heating treatment at 150 to 200 DEG C;

adding the crotonamide and the ethyl acetate, stirring and cooling by a cooler to about 25 DEG C;

the crushed bamboo fiber powder is dried at the temperatures of more than 50 DEG C;

the mixture obtained in the step (1) is extruded to a PP sheet material at the temperature of 210-230 DEG C;

the die is processed through preheating treatment, and the preheating temperature is between 80 DEG C and 120 DEG C;

adding the reacting monomer to polymerize under normal pressure at 72-80 deg. c in the stirring condition;

lowering the temperature to 60 deg. c and adding thickener;

the particles below 80 mesh are placed below 15 DEG C again and re-form the yellow block for repeated use;

secondly, drying soft gum base at 50 to 70 DEG C, grinding sugar;

blanching: blanching the cut noodles for 0. 5-20 minute(s) at a temperature of 50-100 DEG C to obtain cooked noodles;

you can see the red hot when the temperature rise to about 500 deg . c

roasting assembled main core inside braze welding furnace at 230-280 deg. c for 30-60 sec;