closed position

To prepare for the next exposure, the front curtain returns to its normal closed position.

The hand wheel is always in the same position relative to the valve body regardless of whether the valve is in the open or closed position.

When locked in the closed position, the system controlled by the lockout valve cannot be operated until the padlock is removed.

Where valves must be locked out for safety reasons, valve can be locked in the open or closed position.

A backup stem seal for a gate valve retains pressure in the body when the valve is in the closed position.

when the coil to form a power outage, back in the spring and fluid pressure, the spool back to the closed position, the engine shutdown.

Two inductive sensors mounted one on top of another in one housing give a precise indication of the open and closed position of a valve.

A shutoff gate is associated with each connecting trough and movable between an open position and a closed position.

After fitting of the valve, the valve should be maintained in a closed position to prevent any contamination from entering the cylinder.

An assembly structured to selectively orient a seal between an open position and a closed position.

limit switch back to the hearing: long-distance transmission valve open or closed position signals (explosion proof available).

A main storage compartment is formed by the first and second sections when in the closed position and serves to hold the instrument module.

In Electric actuators, the primary limit switches are used to control the open and closed position of the valve.

Valves should be installed with the disc in the closed or almost closed position. This will prevent damage to the disc sealing edge.

In the device's 'closed' position, the keyboard flips back up and is automatically turned off.

back to the hearing: long-distance transmission valve open or closed position of the signal.

diving rigs drilling, generally when the completion of a bored pile a motor to check the closed position.

The open position exposes substantially more of the air passageway than in the closed position.

In the normally closed position, one end of the capacitor is connected to circuit LO.

Latches are disposed substantially diametrically opposite to the handle for retaining the cover in the closed position.

Where possible, the closed position should be determined by leak test using water or air, under low pressure .

A movable contact arm (26) travels within a channel (54) between the closed position and an open position.

As the fluid stream slows and reverses , the disc responds by swinging to the closed position.

When a trap is failed in the closed position, condensate are accumulating upstream.

They employ a unique, one piece center spool design that accommodates a user-supplied padlock in the closed position.

The spring is under compression, which means that it tries to expand and therefore spring-loads the valve in the closed position.

Valve is shown in closed position.

Set hinge cam on out swinging doors to hold unlatched doors in closed position.

The support nut is screwed onto the support rod against the bias of the spring to secure the window in its closed position.

Sensing: Hall effect sensing is available to sense open & closed position.

Normally closed position, opens when pressure reaches set-point.

The assembly should then be slipped onto the valve stem, with the valve in the closed position.

Valve and pump are electrically interlocked so that power is shut-off when the valve is in near closed position.

The valve may be padlocked in full open or full closed position.

They shook for a second when opening up all the way then for like 5 seconds when they went to the all the way closed position.

Always keep the removable hinged lid attached and in the closed position when not serving.

Disc bolting is then tightened in closed position.

Connected coolant tank to valve pos. 10 (Closed position).

rotate the bolt 90 degrees from the closed position to the open position.

FIGURE 3. - This shows an analogous view of Figure 2, but when the device wheels are in the minimum closed position.

Load contacts 56 and 78 will also change from their normally open or normally closed position when the control energizes .

Well, how can you have closed position in street fighting?

Open the needle valve 2 _ turns from the fully closed position.

Valve and pump are electrically interlocked so that power is shut-off when valve is in a near closed position (adjustable with limit switch)

The valve should be closed once, taking the valve from the full-open position to full-closed position;

Into a shut or closed position:

If for any reason the valve closed position reads other than 0-0, the following procedure should be followed

load contacts 5 - 6 and 7 - 8 will also change from their normally open or normally closed position when the control energizes