| 单词 | carburizing |
| 释义 | 例句释义: 渗碳,增碳,碳化,渗碳剂,渗碳处理,渗碳法 1. Steel for carburizing is usually a low-carbon steel of about 0. 15% carbon that would not in itself responds appreciably to heat treatment. 用于渗碳的一般是含碳量约为0.15%、本身不太适合热处理的低碳钢。 www.mapeng.net 2. Carry out a research into the application of bipolar thyristor to the carburizing furnace control system. 对双向晶闸管在渗碳炉控制系统中的应用进行了研究。 www.chemyq.com 3. CYCLE TIME : Amount of time product spends in a furnace at specified temperature for the purpose of carburizing or hardening product. 周期：产品在炉中某特定温度下渗碳或硬化所需要的时间。 www.chuangjiyuan.com 4. The feature of the microstructure of the silicon- aluminizing coating and its anti-carburizing property were analyzed and studied. 分析了铝硅共渗层的组织特点，研究了处理层的抗渗碳性能。 dictsearch.appspot.com 5. The amount and the depth of carburizing on the casting surface can be obtained approximately by a calculating formula. 给出了铸件表面增碳大小及增碳层深度的近似计算公式。 www.chemyq.com 6. Low temperature plasma carburizing is an effective process of improving mechanical property of austenitic stainless steel. 低温离子渗碳处理是一种能改善奥氏体不锈钢表面力学性能的有效方法。 www.13191.com 7. Carburizing, cyaniding, and induction hardening are some of the processes commonly used to produce the case hardening effect. 碳化、氰化、感应淬火是局部淬火中经常使用的处理方法。 zhidao.baidu.com 8. The carburization rate can be increased 20% compared with the conventional carburization process by using RE catalyzed carburizing. 采用改进型稀土催渗剂进行渗碳后，与常规渗碳工艺相比提高渗碳速度20%； dictsearch.appspot.com 9. Meanwhile the carburizing speed is increased, the metallurgical structure is improved, the satisfactory results are obtained. 同时提高渗速、改善金相组织，取得满意效果。 lib.cqvip.com 10. The better technological process now is the step control of carbon potential during carburizing . 目前最佳渗碳工艺方法，是在整个渗碳过程中对碳势进行台阶式控制。 dictsearch.appspot.com 1. Brick-Die After carburizing treatment (heat treatment), complete sets of mechanical dragon brick after all embalmed. 制砖机模具经过渗碳处理（热处理），成套金龙制砖机械全部经过防腐处理。 baike.china.alibaba.com 2. and then carrying out molding and pre-sintering, carrying out mechanical press-fitting and the sintering-soldering, and finally carburizing. 接着进行成形和预烧结，然后进行机械压配和烧结焊，最后进行渗碳即可。 ip.com 3. Nonsymmetrical carburizing may also contribute to distortion. 渗碳的不对称也可能导致变形。 zhidao.baidu.com 4. The gear reducer for high strength steel carburizing, carburizing hardening, low noise transmission. 减速器的轮为高强度渗碳钢，经渗碳淬火处理，传动噪音低。 ruiri.net 5. The results show that the carburizing hardening and high frequency induction hardening can debase the profile accuracy by about 25%. 研究结果表明：渗碳淬火和高频感应淬火对齿形精度误差的影响都在25%左右； www.juhe8.com 6. Pack carburizing consists of placing the parts to be treated in a closed container with some carbonaceous material such as charcoal or coke. 固体渗碳的方法是将要处理的零件与木炭或焦炭这些含碳的材料一起放入密闭容器。 www.mapeng.net 7. RE- Carburizing test with solid powder rare earth accelerant in the sealing box multi-purpose furnace was in progress. 采用固体粉末状稀土催渗剂在密封箱式多用炉中进行了C Re共渗试验。 dictsearch.appspot.com 8. It can be quenched in a controlled atmosphere, thin carburizing, carbonitriding heat treatment process. 它能在可控气氛下进行淬火，薄层渗碳、碳氮共渗等热处理工艺。 www.chinafastener.biz 9. The residual life of the tubes is estimated based on the carburizing damage analysis. 在考虑渗碳损伤的前提下对炉管的剩余寿命进行了评估。 www.chemyq.com 10. A new forge residual heat isothermal normalizing technique for alloy carburizing steel is put forward. 针对合金渗碳钢锻（轧）件，研发了一种新的利用锻造余热等温正火热处理工艺。 dictsearch.appspot.com 1. Two carburizing processes were adopted, before or after the hydrothermal reaction. 进行了水热前和水热后两种渗碳工艺研究。 www.boshuo.net 2. The furnace atmosphere was calculated under the condition of carburizing in the nitrogen-methanol based atmosphere in this paper. 本文是采用氮、甲醇基渗碳气氛渗碳，对炉内气氛进行计算。 www.chemyq.com 3. The method of eliminating carbon can solve availably carburizing defect of steel casting was proved by practical production. 实践证明这种工艺方法可有效地解决铸钢件的增碳缺陷问题。 rjggy.net 4. The sample of carburizing makes the component and hardness analysis. 对渗碳后的试样停止了成分和硬度剖析。 www.0717zx.com 5. This article recommends the process of direct quenching after carburizing for sucker rod pump liners. 介绍了抽油泵衬套渗碳后直接淬火处理工艺。 www.chemyq.com 6. The low-temperature RE carburizing technology is explored by a series of tests. 通过一系列试验，摸索出利用稀土低温渗碳技术。 lib.cqvip.com 7. Effect of silicon on microstructure and properties of meta-bainitic carburizing steel were studied. 研究了硅对准贝氏体渗碳钢渗碳组织与性能的影响。 www.chemyq.com 8. So RE slat liquid carburizing may replace poisonous cyanide slat bath or "603" slat liquqid carburizing. 可取代剧毒的氰盐和微毒的“603”盐浴渗碳。 www.chemyq.com 9. Direct quenching after carburizing can meet technical requirement in order to save working time and cost. 为节省工时和成本，渗碳后采用保护性气氛加热直接淬火可以达到技术要求。 rjggy.net 10. repeatedly forged iron, based on ancient block of iron also find the experience of carburizing Cheng Gang, this is the first steel to steel. 在反复锻打铁块的基础上，古人又找出块炼铁渗碳成钢的经验，这种钢地就是最早的钢。 www.qiyeku.com 1. Pressing bolt from the steel by carburizing treatment, enhance the surface hardness and wear resistance; 榨螺由合金钢经渗碳处理，增强表面硬度和耐磨性； shebei.waimao8.com 2. Study of Plasma Carburizing Process for Stainless Steel and Microstructure and Mechanical Properties of the Carburizing Layer 不锈钢等离子渗碳工艺及渗层组织和性能的研究 www.ilib.cn 3. Design for hardening press die of outer races of double row tapered roller bearing made of carburizing steel 渗碳钢双列圆锥滚子轴承外圈淬火压模设计 ilib.cn 4. Study of the Are-added Glow Discharge Plasma Non-hydrogen Carburizing on Titanium Alloy Surfaces 加弧辉光离子无氢渗碳在钛合金表面上的应用研究 www.ilib.cn 5. Design and Adjusting of Nitrogen-Based Atmosphere Carburizing Process for a New Mult-Purpose Chamber Furnace 新箱式多用炉氮基气氛渗碳淬火工艺的设计与调试 ilib.cn 6. Conditional stability and efficiency of the finite differential method in the carburizing mathematical model 渗碳数学模型差分算法的条件稳定性和有效性 www.ilib.cn 7. Research and Application of Microcomputer Controlled Gas Carburizing with Chamo Electrical Resistance Method 差模电阻法微机控制渗碳仪的研制及应用 www.ilib.cn 8. RE-Carburizing Technology Used for Gear 齿轮稀土碳共渗工艺 service.ilib.cn 9. Study on the Corrosion Resistance of the Arc-added Glow Discharge Plasma Non-hydrogen Carburizing on Titanium Alloy Surface 钛合金表面加弧辉光离子无氢渗碳耐蚀性能的研究 ilib.cn 10. Search for Distortion Law of Carburizing and Quenching Parts by Statistical Method 用统计法寻找渗碳淬火变形规律 www.ilib.cn 1. Technology Design and Adjusting of Nitrogen -based Controlled Atmosphere of Continuous Carburizing Furnace 连续式渗碳炉氮基可控气氛的工艺设计与调试 www.ilib.cn 2. Composition Design of the Carburizing Gear Steel Used in Automobile 汽车渗碳齿轮用钢的成分设计 service.ilib.cn 3. Thermodynamics Analysis of Internal Oxidation in Carburizing or Carbonitriding Heat Treatment 渗碳或碳氮共渗时内氧化的热力学分析 www.ilib.cn 4. The apply of a PID controller of self- turing parameter in carburizing furnaces 参数自整定PID控制器在渗碳炉中的应用 beta.ilib.cn 5. Research of Reasonable Selection of Carburizing Stage and Diffusion Stage During Gas Carburizing Process by Using Numerical Simulation 用数值模拟方法研究气体渗碳强渗期与扩散期的合理选择 www.ilib.cn 6. The Reason Analysis and Preventive Measures of the Grinding Cracks of Carburizing Gear in the Procedure of Grinding 渗碳齿轮磨削裂纹的产生机理和预防措施 ilib.cn 7. strength of materials, heat treatment, carburizing, decarburized layer and hardened layer depth; 材料强度、热处理、碳化层、脱碳层和淬火硬化层的深度； www.18show.cn 8. Improvement of the Multiple Impact Contact Fatigue Resistance of Carburizing Steel 提高渗碳钢多冲接触疲劳抗力的研究 www.ilib.cn 9. Design and Manufacture of Ultra Large Type Gas Carburizing Furnace with Microcomputer Carbon-potential Control 微机碳势控制超大型气体渗碳炉的设计和制造 www.ilib.cn 10. Effects of carburizing time on microstructure and transverse rupture strength of graded cemented carbides 渗碳时间对梯度硬质合金显微组织和抗弯强度的影响 www.ilib.cn 1. Friction and Wear Behavior of Non-Hydrogen Carburizing Layer on Titanium Alloy Surface Prepared by Arc-Added Glow Discharge Plasma 钛合金表面加弧辉光离子无氢渗碳层的摩擦磨损性能研究 ilib.cn 2. The Overview for the Automobile Carburizing Steel Conditioning Treatment 汽车渗碳钢预先热处理综述 www.ilib.cn 3. Application of the Process 'Direct Quenching After Carburizing' in Locomotive Driving Gears 渗碳后直接淬火工艺在机车牵引齿轮上的应用 www.ilib.cn 4. The Hardware Design of the Control System for the Carburizing Heat Treatment Furnace 热处理渗碳炉控制系统硬件设计 www.ilib.cn 5. Calculating Method of Reasonable Formulating Carburizing and Quenching Process 合理制订渗碳淬火工艺的计算方法 www.ilib.cn 6. Specification for Steel Forgings, Alloy, for Carburizing Applications 渗碳用合金钢锻件规范 www.mapeng.net 7. Study on Selecting Material and Composite Carburizing Strengthening Treatment for Heat Forging Die 热镦开式模选材与复合渗强化处理研究 www.ilib.cn 8. Selection of Matrix Material and Study on Composite Carburizing Strengthening Treatment for Nut Heat Forging Die 螺帽热镦凹模的选材与复合渗强化处理研究 service.ilib.cn 9. Application Researches and Discussion on ECM Low Pressure Vacuum Carburizing Technology ECM低压真空渗碳技术应用研究与探讨 ilib.cn 10. Energy Savings Using a Combination of Carburizing Cycle Reduction and Intensive Quenching 缩短渗碳周期与强烈淬火相结合的节能热处理技术 www.ilib.cn 1. Microstructure and Properties of Low Alloy Steel with High Carbon Concentration Carburizing 低合金钢高浓度渗碳的组织与性能 www.ilib.cn 2. Heat Treatment Distortion of Heavy Carburizing Gear Ring and Its Control 大型渗碳齿轮圈热处理畸变与控制 service.ilib.cn 3. Heat Treatment of Buick Automatic Transmission Parts in Low-Pressure Vacuum Carburizing Furnace 别克自动变速器零件在低压真空渗碳炉上的热处理 ilib.cn 4. Development and application of high strength automotive carburizing gear steels 高强度汽车渗碳齿轮钢的发展及应用 ilib.cn 5. Approaching on Cutting Pick Isothermal Quenching inside Gas Carburizing Furnace 用气体渗碳炉进行采煤机截齿等温淬火的工艺探讨 www.ilib.cn 6. The Application of New Technology to Seal up Box Type Carburizing Furnace Main Construction 新技术在密封箱式渗碳炉主要构件中的应用 www.ilib.cn 7. Study on Carburizing Furnace of Direct Atmosphere Preparation with Energy Saving and Catalyzer 直生式省能型渗碳炉及催化剂的研究 www.ilib.cn 8. Investigation on Structure Optimization of Carburizing Agent 增碳剂组成及结构优化的试验研究 www.ilib.cn 9. Standard Specification for Carburizing Steels for Anti-Friction Bearings 用于耐摩擦轴承的渗碳钢的标准规范 www.mapeng.net 10. Application of pressure carburizing technology 压力渗碳工艺试验与应用 service.ilib.cn 1. Research on internal oxidation in nitrogen-based carburizing atmosphere 氮基气氛渗碳中的内氧化研究 www.ilib.cn 2. Actual Application of Controlled Atmosphere Carburizing with Acetone and Air 丙酮和空气可控气氛渗碳的实际应用效果 www.ilib.cn 3. Study on Low Temperature Gas Multielement Co-penetration on Alloy Carburizing Steel Surface 合金渗碳钢表面低温气体多元共渗研究 service.ilib.cn 4. Hardenability and Heat Treatment Distortion of Carburizing Steel 渗碳钢淬透性与热处理变形 ilib.cn 5. Hardenability of Carburizing Steel and Heat Treatment Distortion 渗碳钢的淬透性与热处理畸变 www.ilib.cn 6. Carburizing steel alloying development and the influence of alloy element to carburizing steel 渗碳钢合金化发展及合金元素对渗碳钢的影响 service.ilib.cn 7. The Application of Bipolar Thyristor to the Carburizing Furnace Control System 双向晶闸管在渗碳炉控制系统中的应用 www.ilib.cn 8. study on gas carburizing technique of instillation with kerosene - carbinol 甲醇滴注式气体渗碳工艺的研究 www.ichacha.net 9. To know heat treatment of carbon nitrogen, carburizing and protected quenching etc; 懂热处理渗碳，碳氮共渗，光亮淬火等； www.job002.com 10. The Application and Development of the Large-type Non-tube Carburizing Continuous Production Lines 大型连续无罐渗碳生产线的应用与发展 www.ilib.cn 1. Induction Furnace Carburizing Furnace; 感应电炉炉内增碳； wgtwm.e-998.com 2. Analytic method to calculate the carbon concentration in multi-stage carburizing 多段法渗碳碳浓度分布的解析计算方法 www.ilib.cn 3. Double-Glow Discharged Plasma Non-Hydrogen Carburizing on Titanium Alloy Surface 钛合金表面辉光无氢渗碳的研究 scholar.ilib.cn 4. Technology of Altering Temperature and Low-pressure Carburizing 变温低压渗碳技术 www.ilib.cn 5. Simulation Study on Fluidized Bed Carburizing Layer Depth Mathematic Model 流态化渗碳层深度数学模型仿真研究 service.ilib.cn 6. Wear-Resistant Alloying Layer of Plasma Surface Chromizing and Carburizing 等离子表面渗铬渗碳耐磨合金层 ilib.cn 7. Study on Punched Electrotechnical Steel Sheet Carburizing 电工钢冲片渗碳问题研究 ilib.cn 8. Accelerating Effect of Rare Earths in Steel on Its Surface Carburizing Process 钢中稀土对表面渗碳的促进作用 168.160.184.82:8080 9. Renovation on continuous carburizing furnace 对连续渗碳炉的技术改造 www.ilib.cn 10. Research of Carburizing Atmosphere Distribution in Mesh-Belt Furnace 网带炉中渗碳气氛分布的研究 www.ilib.cn 1. Development and Application of the Huge Pit Furnace for Gas Carburizing 超大型井式气体渗碳炉的研制和应用 service.ilib.cn 2. Measures for Reducing Carburizing and Quenching Distortion of Planet Gear 减少大行星齿轮渗碳淬火畸变的工艺措施 service.ilib.cn 3. Special Solid Thermocouple for Carburizing Furnace 渗碳炉用特种实体热电偶 scholar.ilib.cn 4. Application of Medium Silicon Nodular Cast Iron Pot for Carburizing Hand Sewing Needles 中硅球墨铸铁坩埚的应用 www.ilib.cn 5. Rapid Carburizing Process by Increasing Furnace Pressure 快速压力渗碳工艺 www.ilib.cn 6. Development of Continuous Automatic Production Line Technology for Gas Carburizing 连续式气体渗碳炉自动生产线技术的发展 www.ilib.cn 7. Choice for the Material of Carburizing Gear and the Research of Hardening Technology 渗碳齿轮材料的选择及硬化技术 service.ilib.cn 8. Research Status on Distortion Control of Carburizing and Hardening Gears 渗碳淬火齿轮畸变控制技术的研究现状 www.ilib.cn 9. Design Improvement of Double Track Pusher Carburizing Furnace 双排推杆式渗碳炉设计的改进 www.ilib.cn 10. Experimental Verification of CAD Software for Gas Carburizing 气体渗碳CAD软件的试验验证 www.ilib.cn 1. Control of Deformation for Thin Plate-type Gears during Carburizing and Quenching 薄盘类齿轮渗碳淬火变形的控制 www.ilib.com.cn 2. Calculation of Nitrogen-Based Atmosphere in the Carburizing Furnace 氮基气氛渗碳炉内气氛计算 service.ilib.cn 3. Application of PC Controlling in Carburizing Technology 微机控制在渗碳工艺中的应用 www.ilib.cn 4. Study on the wear resistance of three carburizing structural steel after different chemico-thermal treatment 三种渗碳结构钢经不同化学热处理后耐磨性的研究 www.ilib.cn 5. Improvement on Carburizing and Quenching Process for Spindle of Machine Tool 机床主轴渗碳淬火工艺改进 www.ilib.cn 6. Studies and Application of Carburizing and Quenching of Sleeve on the Roll End for High Speed Mills 高速轧机辊端轴套渗碳淬火工艺研究与应用 www.ilib.cn 7. Study on the abrasion behavior of carburizing carbonitriding steel for pump body 碳氮共渗钢水泵体的磨损特性研究 www.ilib.cn 8. Study on high activity catalyst of partial oxidation of PB gas producing carburizing gas 丙烷部分氧化制渗碳气用高活性催化剂的研究 www.ilib.cn 9. Methods of measuring case depth hardened by carburizing treatment for steel 钢的渗碳硬化层深度的测量方法 www.chinastandard.com.cn 10. Double Glow Plasma Carburizing Without Hydrogen of Titanium Alloy 钛合金双层辉光无氢渗碳 service.ilib.cn 1. Application of Computer Control System in Gas Carburizing Furnace 计算机控制系统在气体渗碳炉上的应用 www.ilib.cn 2. Low-temperature Carburizing with Rare Earth Elements for Tractor Gears 拖拉机齿轮的稀土低温渗碳 www.ilib.cn 3. Specification for carburizing steels of bearings 渗碳轴承钢技术条件 www.zftrans.com 4. Finite Element Calculation for Test of Case-Depth Using Eddy Current in Carburizing 涡流检测渗碳层深度中磁感应强度的计算 ilib.cn 5. Development of the Computer Simulating Software on Carburizing Process of Common Shape Parts 常见形状零件气体渗碳过程计算机模拟软件的开发 www.ilib.cn 6. Process and Equipment of Acetylene Low Pressure Carburizing 乙炔低压渗碳的工艺及装备 service.ilib.cn 7. Carburizing and Anti-carburizing for Ethylene Cracking Tube 乙烯裂解炉管的渗碳与抗渗碳 www.ilib.cn 8. Research on High-density Carbonization of Carburizing Steel 渗碳钢高浓度渗碳的研究 service.ilib.cn 9. Re-exploring on Catalyzing Mechanism of Carbonate in Pack Carburizing 再论固体渗碳剂中碳酸盐的催化机理 www.ilib.cn 10. RQD Series Huge Precision Controlling Pit Furnace for Gas Carburizing RQD系列大型精密控制井式渗碳炉 service.ilib.cn 1. Paper searches on the effective hardening layer of carburizing gears 关于渗碳齿轮有效硬化层的探讨 service.ilib.cn 2. An analysis on microstructures of alloyed layer by doubleglow plasma W-Mo alloying process after carburizing 双辉离子渗钨钼层渗碳组织的电镜分析 www.ilib.cn 3. Problem and Improvement of Carburizing and Quenching for Plate Parts 板材零件渗碳淬火中出现的问题及改进 www.ilib.cn 4. Improvement on Carburizing and Quenching Process for Gears 齿轮渗碳淬火工艺的改进 service.ilib.cn 5. Middle-Deep Case Carburizing in Supporting-Roller Type Mesh Belt Furnace 中深层渗碳在托辊式网带炉上的应用 www.ilib.cn 6. Take correcting measures to prevent deformation after the carburizing quenching to large module gears 大模数齿轮渗碳淬火变形的改进措施 ilib.cn 7. Study and Application of Pulse Gas Carburizing Technology 脉冲式气体渗碳技术研究和应用 www.ilib.cn 8. Pasty Carburizing Technology and the Effect of Post-Carburization Heat Treatment on Wear-Resistance of the Carburized Layer 膏剂渗碳工艺及渗后热处理对其渗层耐磨性的影响 www.ilib.cn 9. Study on Arc-added Glow Discharge Plasma Non-hydrogen Carburizing Technology on Surface of Titanium Alloy 钛合金表面加弧辉光离子无氢渗碳工艺的研究 ilib.cn 10. selection of carburizing agent is the key of melting with full steel scrap charge; 增碳剂的选用是全废钢熔炼的关键； www.ceps.com.tw 1. Measurement on the carburizing or nitro-caburizing harden case depth of sintering iron-based material 烧结铁基材料渗碳或碳氮共渗硬化层深度的测定 www.zftrans.com 2. Research of Surface Carburizing on Titanium Alloys by Electrospark Deposition 钛合金电火花表面渗碳研究 www.ilib.cn 3. Study on Pressure Carburizing Technology 齿轮压力渗碳工艺研究 service.ilib.cn 4. Low-carbon Bainitic Steel Carburizing and Its Application in Car Gear 低碳贝氏体钢渗碳工艺及在轿车齿轮上的应用 www.ilib.cn 5. The Model for Gas Carburizing and Calculating of Physic Parameters 气体渗碳数学模型及物理参数的计算 www.ilib.cn 6. Research on Deep Layer Carburizing Technology for Large Gears 大型齿轮深层渗碳工艺的研究 www.ilib.cn 7. Analysis of Gear Quality after Carburizing and Quenching 浅谈齿轮渗碳后淬火的质量分析 www.ilib.cn 8. The Effect of Arc-added Glow Discharge Non-hydrogen Carburizing on Surface Roughness of Titanium Alloy 加弧辉光离子无氢渗碳对钛合金表面粗糙度的影响 ilib.cn 9. The Optimization of Gas Carburizing Technique 气体渗碳工艺参数的优化 www.ilib.cn 10. Carburizing and Nitriding of Ferrous Metals in Ancient China 中国古代的钢铁渗碳和渗氮技术 www.ilib.cn 1. Development of Vacuum Carburizing Technology at Home and Abroad 真空渗碳技术国内外概况及发展 www.ilib.cn 2. carburizing quenching and tempering of steel 钢渗碳淬火及回火加工 blog.sina.com.cn 3. Development of low pressure carburizing technology 真空渗碳技术的进展 service.ilib.cn 4. Diffusion Equation Answer of Double-period Carburizing by Using the Mathematical Analysis 两段法渗碳扩散方程的解析解 www.ilib.cn 5. Process Control in Thick- layer Carburizing for Heavy-Duty Gear 重载齿轮深层渗碳的工艺控制 service.ilib.cn 6. The Carburizing Heat Treatment CAPP System of Bevel Gears of Precision Die Forging 精锻锥齿轮渗碳热处理CAPP系统 ilib.cn 7. Study on the Effect of Pattern Materials on the Steel Casting Surface Carburizing in EPC Process 模样材料对气化模铸钢件表面增碳影响的研究 www.ilib.cn 8. Effect of Silicon on the Microstructure and Properties of Meta-Bainitic Carburizing Steel 硅对准贝氏体渗碳钢组织与性能的影响 service.ilib.cn 9. Act of Hydrogen in the Carburizing Process and Post Heat Treatment 氢在渗碳及其后热处理过程中的行为 scholar.ilib.cn 10. The depth measurement of carburizing layer 渗碳层深度测量 wenku.baidu.com 1. Hardware Design of the Control System of Carburizing Furnace Based on Single-chip Microcomputer 渗碳炉单片机控制系统的硬件设计 service.ilib.cn 2. A Study on Gear Pressure Carburizing and Induration 齿轮压力渗碳及硬化工艺研究 service.ilib.cn 3. vertical pit-type gas carburizing furnace 井式气体渗炭炉 www.hxen.com 4. The Effect of Rare Earth Element on Structure Heredity of Deep Carburizing Steel 稀土深层渗碳钢晶粒长大及组织遗传研究 www.ilib.cn 5. Distortion Reduction Method of Carburizing Taper Gear Splined Hole 减少渗碳齿轮花键孔变形的方法 www.ilib.cn 6. Use carburizing for high nickel content parts 渗碳适用于含镍高的零件 wenku.baidu.com 7. Improvement of Workholders for Gas Carburizing Pit-type Furnace 井式气体渗碳炉工装改进 www.ilib.cn 8. The Study of Application of RareEarth Elements in Carburizing Technology 稀土元素在渗碳工艺中的应用研究 service.ilib.cn 9. Effect of Sulphur in Natural Gas on Carburizing Process 天然气中的硫对渗碳的影响 www.ilib.cn 10. Carburizing and Quenching of Roll End Sleeve 辊端轴套的渗碳淬火 www.ilib.cn 1. New-type BBH Series Gas Carburizing Furnace 新型BBH系列箱式气体渗碳炉 www.ilib.cn 2. The Reaserch and Application of Low-Deep Carburizing Process 浅层渗碳工艺方法研究及应用 ilib.cn 3. Discussion on Banded Structure of Carburizing Alloy Steel 浅谈合金渗碳钢带状组织 www.ilib.cn 4. Aging of Solid Carburizing Agent 固体渗碳剂的老化 service.ilib.cn 5. Gear Pre-oxidation Gas Carburizing at Low Temperatrue 齿轮预氧化低温气体渗碳 www.ilib.cn 6. New Process of Drop Feed Gas Carburizing with High Rate 滴注式快速气体渗碳新技术 www.ilib.cn 7. A Study on the Carburizing Velocity 关于渗碳速度的研究 www.ilib.cn 8. A New Kind of Anti-Carburizing Paint 一种新型防渗碳涂料 www.ilib.cn 9. ENDT for carburizing depth of steel parts based on RBF ANN 基于RBF神经网络的渗碳层深度电磁无损检测 www.ilib.cn |
| 随便看 |
|
英汉双解词典包含2704715条英汉词条，基本涵盖了全部常用单词的翻译及用法，是英语学习的有利工具。