valve body

The utility model belongs to an improvement for a safety valve of a pressure cooker, comprising a valve body, connecting nuts and a plug.

The next section involves a change in length to the valve body that requires a corresponding change to the length of the link.

The hand wheel is always in the same position relative to the valve body regardless of whether the valve is in the open or closed position.

The body side seat has a rib molded into the seat ring which locks into a groove in the valve body.

Robust cast iron valve body with a fabricated rotor, polyurethane adjustable replaceable blades and a direct drive.

Position the bottom flange cover on the bottom of the relief valve body and secure by hand tightening the four bottom bolts.

actuator head with a hardened steel shaft in a bronze bearing is mated to a solid aluminum valve body.

The utility model relates to a multiple-way valve, comprising a conical multiple-way valve body and a valve core.

Stellite faced Seat Rings are welded into the body. This provides a positive no-leak seal of the ring in the valve body.

Even though the valve is not thoroughly cleaned after sampling, the sterile state of the valve body can still be well ensured.

A packing sealing structure is arranged between the valve rod and the upper end of the valve body.

and the valve core (8) is arranged on a channel between the air inlet and air outlet of the valve body (2) in an opening manner.

The boss at the bottom of the valve body is regularly tapped at the factory.

All internal parts accessible by removing blind flange or spring chamber. Regular maintenance can be performed with the valve body in line.

The middle of the valve body is provided with a radial air outlet pipe to make the valve body in a three-way shape.

The theoretically optimum size of the valve body was obtained, its strength improved, and stress distribution in it made uniform.

Valve body shall be drilled and tapped for a pressure connection on top and bottom of the housing.

Lift retainer and check assembly from valve body. To assist with removal a small flow can be applied by "cracking" the inlet valve slightly.

The two halves shall be sealed by diamond shaped cross section rubber gasket permanently locked by a groove in the valve body.

the other way passes through each color ink to be connected with the valve body adjacent to each sprayer by each ink injecting pipeline.

Beneath the handwheel is one set of wrench flats on a nut threaded into the valve body.

Remove handwheel and turn indicator sleeve by grasping the handwheel and pulling away from the valve body along the stem.

The valve body expansion pipe is only used to open or close the valve, but can not replace the expansion pipe in the pipe.

Valve Body, Cover, Tailpiece and Control Stop shall be in conformance with aSTM alloy Classification for Semi-Red Brass.

The oil is then sent, under pressure to the pressure regulator, the valve body and the rest of the components, as required.

Sealing tightness is ensured by the compression of the sealing rings against the piston and valve body.

The thimble and valve body has the thread connection, the place around the thimble has the flange.

Fine basin faucet valve body is made of bronze and its surface has Cr coating, gold coating and other various color coating.

Slide the other half of the splash guard into the groove on the relief valve body and reassemble the two parts together .

Said device comprises a valve, the valve body (34) of which can be operated by means of a float (14) in the dampening solution (12).

Flexible sealing valves, seals can be mounted on the valve body or attached to the butterfly plate peripheral.

The check valves shall be modular and shall seal to the main valve body by the use of an O-ring.

The Lunar Ball Segment Valve has a full-bore opening where material cannot build up, accumulate, or be captured within the valve body.

A step on the valve plug has now been back-seated against the upper portion of the valve body (metal-to-metal).

the structural length of the valve body is shortened.

The valve body acts as a built-in actuator, eliminating costly hydraulic, pneumatic, or electric operators.

B. filter net is set on the net ring bracket and straight-flow channel is formed between the outlet port and the inlet port of valve body.

apply heat with flame directed away from the center of the valve body . excessive heat can harm the seats.

Both the retainer side and the body side seats are locked into the valve body.

This analysis method and conclusion provides theory proof for time effect of vibration technology for eliminating valve body remains stress.

and the elastic piece is arranged in the chamber of the valve body and presses the second end of the piston eccentrically.

The valve body will provide equivalent maximum flow rates of standard butterfly valve bodies of the same diameter.

In case of fire, the detector will work. Spring of valve body will close the open and close valve.

The valve body (10) has elastic properties and a normal shape when it abuts against the valve seat so that it closes the valve means (9).

The volume and the number of technological holes of valve-body were reduced to a large extent.

The leaf blade joining fitting is consistent, should implement the grouping adjustment with the valve body seam wind valve.

Introduces the structure, characteristics and mechanical machining methods for T-type Sodium globe valve body.

and the steam adjusting shaft does linear motion in the steam valve body so as to open and close the steam inlet and the steam outlet.

2, Special structure and reliable performance. The hose can be changed in regular time and valve body can be used for a long time.

Install valve in the line with arrow on valve body pointing in the direction of flow.

Install valve in the direction of the flow arrows on the valve body.

a sewage connector is arranged on the valve body and communicated with the inner cavity of the valve body.

and the pipeline port of the inner cavity of the valve body is provided with the valve seat matched with the valve plate.

The upper set of wrench flats belong to the packing nut, which is threaded into the valve body.

Install with the arrow on valve body pointing in the direction of flow.

Turn handle to be perfectly perpendicular to valve body.

The valve seat of the integrative type, the valve body, valve seat connection question exist.

After removing the first check from the backflow valve body, place on a flat surface with the coil spring facing up.

According to the simulation results, a method to improve the valve body strength is presented to optimize the design of the valve system.

A force application mechanism allowing the valve plug to closely cling to the flat plate is arranged in the valve body.

Remove the body bolts from valve body using Allen Key.

An aircraft nose shaped air guide sleeve is arranged at the liquid inlet of the valve body.

Kits include: Rubber Disc, Piston Diaphragm Assembly, disc retainer, Relief valve body O- ring.

Cleaning the valve body bore and the disc, check each part for damage phenomenon, the connection voltage tightened.

The S45 type valve has a forged brass valve body, and is suitable for hot or cold water devices requiring in-line mounting.

Installation suggestion: valve body vertical and upward .

At the same time, the stress analysis of the control valve body was shown by considering the fluid-structure interaction.

Some small acetylene cylinders, Type B or MC size cylinders, are equipped with fusible plugs in the valve body.

Pay attention to the flow direction of medium and install the valve referring to the indicating arrow on the valve body.

Note: To prevent damage to valve from excessive heat during soldering, remove unions and gaskets from valve body prior to soldering.

The seal may be a single-piece or a multi-piece assembly press-fit into the valve body.

Remove first check module from valve body and insert complete with O - ring in plug module adaptor.

The wellhead throttle valve is made up of nozzle, plunger-shaped spool, throttle value, valve body and valve rod, etc.

Remove the body bolts from the valve body.

In the first section, you investigate involve interferences between your solid link part and the internal cavity of the valve body.

In this tutorial, the assembly is a simple valve and the first part placed is the valve body.

Thoroughly clean all inside surfaces of the relief valve body .

Pay attention to the direction of medium in valve body. Add seal cushion between two flanges connection and screw down bolt.

For initial testing, a valve body diameter similar to the one typically used on the application can be used.

Do not allow any pipe dope into valve body in order to avoid damage to disc and seat.

Assigning the ideally fitted wedge, ground and lapped, to proper valve body.

The valve body of the valve is provided with upper and lower two valve cores.

Rotate one half of the valve body 180o making sure the lower valve seat and oring stay in position.

Based on the mathematical model, the influence of piston valve body's elastic modulus and deflected disc's elastic modulus are analyzed.

Check modules are installed in the valve body with the seats facing the valve inlet.

The top of retainer must drop just below threads in the valve body.

The valve mainly by the valve body, valve cover, valve flap formed.

All internal valve components shall be removable and repairable while the valve body remains in line.

The whole valve body is a building block type composite structure.

Company name and location shall be cast onto the valve body.

Install the check modules into the valve body hand-tight.

Insert two bolts of specified size (Table 1) to secure the halves of the flange adapter to the valve body (Fig. 2).

Insert valve body through mounting hole and seat lugs .

Beneath the hand wheel are two nuts attached to the valve body.

The valve mechanism contains a valve body with the oil line.

In this thesis, ZG35CrMo valve body was mainly studied. The pipeline valve body should pass hydraulic pressure test for 70MPa.

The combined type valve body is divided into an outer type valve body or a built-in type valve body.

Based on the maximal speed of the working plunger, the structure of valve body and open schedule of distributors spool were optimized.

100% ultrasonic testing of important welded parts such as valve body, disc, servomotor cylinders, upstream and downstream piping.

the valve cover and valve body junction.

Change the color of the valve body.

In addition, its brass bonnet and valve body makes the M70 an excellent choice for use in sensitive applications.

It is held in place by the bonnet which is attached to the valve body by studs and nuts.

For outfeed, the valve body (10) assumes a stretched shape and leaves the valve seat.

A second stream or flow path "FP2" is defined by fluid flowing through flow control element 354 into cavity 218 in valve body 212.

Die cast zinc alloy valve body.

Fluid flowing through flow control element 352 is directed into first cavity 216 within valve body 212.

After leaving the packing ring, the arrow-shaped valve body falls to open the lock of the tension releasing control pin.

Three-dimensional Transient Temperature Field of the Valve Body of a Turbine Regulating Valve and the Analysis of Its Stress Field

A vertical rotating and switching device comprises a main valve body, a handle rotating and positioning mechanism and a valve core;

Analysis of the Influence of Valve Body Materials on the Magnetic Field Intensity on an Orifice Using FEM

the outer edge of the middle valve body is provided with two circular installing lugs which are distributed in a hexagon way;

A spring, a piston and a pressure chamber are arranged in the inner cavity of the valve body;

Industry: Reducer, gearbox; Casting; Valve; Body and accessories; Gear; Gear cutting machines; Fertilizer machinery;

A plate-shaped stainless steel filter screen is fixed between the valve body and the valve cover through stainless steel screws;

Structure Optimization Design Study of Turbine Butterfly Valve's Valve Body

the adjusting valve comprises a valve body, a valve rod, a spring and a sealing gasket;

Industry: Solenoid valve; Valve; Industrial Products Agents; Import and Export Agents; Pneumatic valve; Body;

Industry: Integrated companies; Valve; Pneumatic valve; Flow Control Valve; Body; Solenoid valve;

Mold filling and solidification simulation of a valve body casting

Installation, Inspection and Maintenance of Valve Body Pressure Relief Methods for Geothermal and Other High-Temperature Liquid Applications

Industry: Water meter; Gas Meter; Other flow meters; Control (regulation) Instrument; Flow Control Valve; Body;

Application of ultrasonic cleaning technology to painting pretreatment of valve body

Industry: Exhaust valve; Body; Hydraulic machinery and parts; Worm; Worm; Marine Engine Parts;

Industry: Control Valve; Body; Exhaust valve; Solenoid valve; Discharge valve; Gas valve;

a spring is arranged between the piston and the inner cavity of the valve body;

Design of the Foam Mold of Plastic Pattern Fully Shaping for Medium-sized Butterfly Valve Body

Simulation of the Casting Process for Automobile Metal Valve Body

Influence of Specific Pressure Value in Squeeze Casting on Properties of Cu Alloy Valve Body

Corrosion Characteristic Analysis of Valve Body Materials for Relay in Ship

The Assemble Welding Process Research for Bypass Mechanism of Valve Body on the Gas Turbine

a guide stub pipe for guiding the movement of the valve flap is set on the valve body;

Improvement of Foundry Technology on Air Inlet Valve Body and Air Escape Valve Body

The Cause of Valve-body Cracks of High-pressure Bypass Valve

Trial-Manufacturing of Ultra-low Carbon Stainless Steel Valve Body

Design of Hot Extrusion Mould of Roughcast of Multi-joint Thin-wall Brazen Valve Body

Elimination of Shrinkage Porosity of Nodular Iron Valve Body

Processes the valve body with the cubic boron nitrite cutting tool

The Casting Technology for Large Scale Ductile Valve and Valve Body

Steering Apparatus Having Valve Body welded in Input Shaft

Air - tightness testing of the main valve body assembly on 120 - 1 air control valve for freight car

Analysis and countermeasure on valve body crack of NO. 1 And NO. 2 Units'high-pressure bypass-valve in Yuanbaoshan Power Plant

The Development and Prospect of Multi-way Loading Entirety Forming of the Parts Like Three Direct Links Valve Body

The Process for Warm Extruding the Valve Body and Design of the Die

the power structure is installed on the outer side of valve body;

the valve core is rotationally arranged in the centre hole of the valve body;

Electron beam welding procedure of valve body

leave the check assembly parallel to the valve body

Modality and harmonic response analysis of hot breeze valve body based on finite element method

Technique of cold station mending for valve-body

Formation and die design of forging for valve body in mud pump

Various gate valve body casting

oil pressure relief valve body

Analysis on Fracture of Valve Body

Material for the valve body

Bronze Ball Valve Body Styles

Solenoid A - Main Valve Body Cover A

code of materials for valve body

Design of Die for 45 Steel Valve Body in Extruded Casting