voltage-drop

Since the leakage current through the zener diodes results in a voltage drop across the resistor, low leakage zener devices are desirable.

The simulation results under voltage drop show that this coordination control strategy is feasible.

Since the voltage drop across the ammeter is negligible, essentially all the test voltage appears across R.

In DC coupled applications, input impedance is not as important as input current and its voltage drop across the source resistance.

The forward voltage drop in the on-state is only a few volts(typically 1 to 3 V depending on the device blocking voltage rating).

The permissible voltage drop must be such that the signal level can be reliably interpreted at any receiving node.

The amount of voltage used up for each resistor is called the voltage drop across that resistor.

The low input voltage drop (voltage burden) of such a picoammeter keeps the anode at virtually ground potential.

The resulting voltage drop is proportional to the unknown resistance and is indicated by the meter as resistance, rather than voltage.

These resistor values should be such that the voltage drop at the maximum measured current will not affect measurement accuracy.

The next step is to label all voltage drop polarities across resistors according to the assumed directions of the currents.

Measure the reverse breakdown voltage by sourcing a specified re verse current bias, then measuring the voltage drop across the diode.

A pixel for compensating for the threshold voltage of a drive transistor and the voltage drop of a first power source are provided.

Thus, if every part has some resistance, no matter how small, there must be a voltage drop on it when the current is flowing through.

Moreover, as the voltage drop over transparent conductive layer is reduced, the efficiency of the lighting device is increased.

As its resistance increases, its voltage drop increases and, though small, can be measured without difficulty.

The current is sourced through the two outer probes and the voltage drop is measured between the two inner probes.

Application of PC based instrument for ground impedance measurement can overcome the shortcomings in traditional voltage drop measurements.

In particular, if the devices have low resistance, the current flowing through the switches may cause a significant voltage drop.

To further enhance efficiency, the voltage drop across the tracking regulators has been minimized.

This creates a voltage drop, which can be measured to determine position.

While two contacts supply a constant current, the other two contacts measure the voltage drop across a portion of the sample.

Use only high grade insulated wiring of suitable capacity. Undersized wires will cause resistance and consequent voltage drop.

This voltage drop is equal to the product of the current and the resistance, hence it is called the IR drop.

The resistance must BE calculated from the current and the resulting voltage drop using ohm is law.

In the experiments, the relationships between impedance and time, voltage drop and time, were obtained.

The channel resistance may cause a significant voltage drop if the current being switched is high enough.

To mea sure the forward voltage, apply the specified current, then measure the resulting voltage drop.

Thermal losses are significant due to the minimum SCR on state voltage drop.

Now, the common-mode current (ICM) flows through R2, developing a voltage drop, which is added to the voltage to be measured.

And the voltage drop of medium voltage busbar also maybe not satisfies the requirement of biggest motor start-up.

Allegro's A3901 offers a very small package size, low operating voltage and low voltage drop MOSFET outputs.

The voltage drop arises in the semiconductor elements of the sensor.

When the test current is applied, the instrument will indicate the resulting voltage drop.

(neglecting the forward voltage drop of the diode).

Because the value of the shunt resistor is known, you can calculate the mechanical strain corresponding to the voltage drop of the resistor.

The utility model discloses a high-voltage small capacity (lower than 3A) fuse wire which is arranged in a high-voltage drop type fuse.

This reduction is caused by the internal resistance (RM), which creates an additional voltage drop called the voltage burden (VB).

Lower voltage drop between contact tip and wire ?

in order to overcome the weight of cable itself and voltage drop when lifting height is over 100m , we use cable trolley.

Temperature behavior of thyristors conduction voltage drop and its influence on the current balance coefficients

Detection of the Voltage Drop Signals on Thyristors and Trigger Circuit in the Soft-starting Device for Induction Motors

Improvement against the Effect of Voltage-drop on Secondary Circuit of Potential Transformer to the Measurement of Electric Energy

Voltage-Drop Starting Control Circuit Analysis of Three-Phase Asynchronous Motor Autotransformer

Universal Calculation of Effective Voltage Drop of Main Low-voltage Supply Line in a Mining District

Design of A New-type Autotracking Compensator of Voltage Drop on TV Secondary Leads

elements of electrical and optical connection - test methods - voltage drop under specified current for terminal lugs and in - line splices

Analysis and Measurement of Voltage-drop in Secondary Electricity Meter Circuit of Potential Transformer

Measuring forward voltage drop characteristics of PN junction with temperature using computer

Secondary voltage drop automatic compensator in voltage mutual inductor of substation

Analysis on Uncertainty of TV Secondary Circuit Voltage Drop Wireless Detection Instrument

Influence of Mutual Inductor and Secondary Loop Voltage Drop on Precision of Electric Energy Computation

Studies on the C-V characteristics and calculated of voltage drop at interfaces in MFS structure ferroelectric film

Discussion of the Reason and Transformation of PT Secondary Voltage Drop

Measurement of Voltage Drop Error in Secondary Circuit of Potential Transformer

Voltage Drop at the Interface in Multilayer Ferroelectric Films Diode

Electrokinetic Treatment Affected by EDTA and Applied Voltage Drop for Cu Mine Tailings

Aerospace series - Requirements and test procedures for relays and contactors - Part 307: Contact voltage drop

Dynamic stability limit of synchronous motor during power system voltage drop

The New Secondary Voltage Drop Tester for the Potential Transformer

Design of Voltage Drop Self-Adapting Compensation Method for TV Secondary Circuit

The Method for Reducing Voltage Drop of Secondary Side of PT in Electric Energy Measuring Device

GPS-based Test Method and Application for Voltage Transformer Secondary Circuit Voltage Drop

Influences of Second Circuit Voltage Drop Tester on Measurement Error

The Effect of the Frequency on the Voltage Drop of Interface of Multilayer Ferroelectric Film

Section Five Voltage drop, voltage loss and voltage deviation of power network

Use Voltage Drop-Down Resistor to Suppress the Interference from Clock Circuit

Influence of Wirebonding to the Forward Voltage Drop of Schottky Device

Discussion on Differences Between Voltage-Drop and Voltage-Loss

Standard Guide for Measuring Voltage Drop on Closed Arcing Contacts

Power-protected circuit for power station without voltage-drop

Calculation of net voltage drop of solid motor soft starting by Langevin's theorem

Effect of Voltage Drop Error for TV Secondary Circuit on Electric Energy Metering

Accurate Expressions of Voltage Drop and Voltage Loss on Power System

Calculation and Analysis of Voltage Drop of Electric Network

Temperature coefficient of voltage drop

Measuring Voltage Drop on Closed Arcing Contacts

Measuring the Contact Voltage Drop of Relay and Analysis of Data

Voltage Drop in Control Circuit and Solution to the Problem

The study and application of the temperature dependence on the positive-going voltage drop of PN junction

A Static Voltage Drop Analysis Method of Standard Cell Chip

Effect of Pressure on the Contact Voltage Drop of CNT-Ag-G Composite

Break-Up Operation Criterion Based on Voltage Drop of Double-Circuit Lines

high voltage drop-out type fuse cutout

Voltage drop in the arc column