网站首页  词典首页

请输入您要查询的英文单词:

 

单词 tool-holder
释义

tool holder

美 
英 
  • un.夹持器;刀把
un.
1.
夹持器
2.
刀把

例句

释义:
1.
In addition, the cutter of the building height should be as small as possible, to prevent is at the top of the paper is tool holder.
此外,裁纸刀的抬起高度应尽可能小,以防止位于顶部的纸张被刀架带下。
www.bing.com
2.
This theoretical agreement leads with the user to the acceptance that thread taps can be used in rigid tool holder without problems.
理论上同意,操作者可以在致密刀柄上使用攻丝螺纹。
www.baisi.net
3.
The main middle part of the article analyze the movement accuracy when the tool holder has deviation.
然后对刀架系统存在误差时的运动精度分三种情况进行了分析。
www.13191.com
4.
The simulation results are proved that the PID controller based on repetitive control is effective to the motion control of the tool holder.
仿真结果表明基于重复控制的PID控制器能够有效的对电磁驱动刀架的进给运动进行控制。
old.blog.edu.cn
5.
A software named MATLAB is utilized to the tool holder as the simulink and control software.
采用了目前国际上流行的仿真与控制软件MATLAB对所设计的刀架驱动系统进行仿真研究。
old.blog.edu.cn
6.
MODULAR UNITS FOR MACHINE TOOL CONSTRUCTION. TOOL-HOLDER SHANKS WITH "CONE AND FACE" BEARING SURFACES.
机床构造标准部件。“锥面”移动距离的夹具柄
www.mapeng.net
7.
The cooling is realised without any handling, with air, whatever the type of tool-holder, without limited rate.
冷却是实现没有任何处理,空气,无论在何种工具持有人没有限制率。
bzxw.512121.com
8.
Boring bars (tool holder with cyldindrical shank) for indexable inserts. Designation.
配用于可转位刀片的镗杆(有柱形刀柄的刀具夹).名称和牌号
www.mapeng.net
9.
These inserts were clamped mechanically on a rigid tool holder.
嵌入式切削刀片在刚性刀具架上用机械夹具加紧。
zhidao.baidu.com
10.
CNC mill equipped with a multi-tool holder.
配备有多刀架的数控铣床。
www.core.org.cn
1.
CNC (CAD numerical control) lathe with single tool holder.
配备有单刀夹持器的数控铣床。
www.core.org.cn
2.
Single-tool holder within a CNC mill.
数控铣床上的单刀架。
www.core.org.cn
3.
Multi-tool holder within a CNC mill.
数控铣床上的多刀架。
www.core.org.cn
4.
After scraping knife wear-and-replace pboblems cleaning tool holder and envirogluvtm in the blade.
刮不朱刀磨损后调换时给夺目冲洗刀架与不抬刀条边的油不朱。
www.bing.com
5.
Three-dimensional Finite Element Analysis on the Contact Unit of Tool Holder Used in NC Traction Drive
NC机床用牵引驱动增速刀柄接触部件的三维有限元分析
ilib.cn
6.
Analysis on Automatic Tool Holder's Failures of a Economical NC Lathe
经济型数控车床自动刀架故障分析
ilib.cn
7.
Design of a Linear Servo Tool Holder System with High-Frequency
高频大位移微进给直线伺服刀架的设计
ilib.cn
8.
Design of revolving tool holder for machining roller pass with large curvature radius dimension
用于轧辊孔型加工的大曲率半径回转刀架设计
www.ilib.cn
9.
Design of micro-feeding tool holder used in turning machining
车削用微进给刀架设计
www.ilib.cn
10.
Error compensation control of repetitive feedback in servo system for tool holder
伺服刀架系统的反复反馈误差补偿控制
ilib.cn
1.
Tool holder with prism; form A with square transverse seat
燕尾导轨工具夹具.A型带四角横向夹紧器
www.mapeng.net
2.
side knife in the tool holder measured on a size before and after, you should replace the knife shell or calibration tool holder;
侧刀在刀架上测量前后尺寸不一,应更换刀壳或校准刀架;
www.bing.com
3.
Tool holders with parallel shank; survey of tool holder; types and accessories
直柄工具夹具.概览.型式和附件
www.mapeng.net
4.
Mechanism of Tool Holder Tension Adopting Spring and Hydraulic
采用弹簧与液压的刀柄拉紧机构
www.ilib.cn
5.
L knife and tool holder: Rotary cutting tools, rolling the die, tool holder;
l刀模具及刀架:滚切刀具、滚压模具、刀架;
www.bing.com
6.
Electrical Mechanism of Tool Holder Tension in Lathe
车床电动拉紧机构
ilib.cn
7.
Tool holder with prism; form C with more than one square seats
燕尾导轨工具夹具.C型带四角多面夹紧器
www.mapeng.net
8.
Research on Cam Turning Tool Holder Driven by Linear Motor
直线电机驱动的凸轮车削伺服刀架系统研究
www.ilib.cn
9.
Research on the Linear Servo Tool Holder System for Noncircular Cutting
非圆截面车削中直线伺服刀架系统的研究
www.ilib.cn
10.
special tool holder for milling machine
铣床专用刀杆
www.bing.com
1.
Centre post press tool sets with thick top tool holder
带中间立式导柱和厚的柱导板
www.mapeng.net
2.
indexable tool holder for turning tool
机械夹固式车刀杆
www.hxen.com
3.
Diameter of the tool holder
刀杆直径
www.nmt2.cn
4.
Use of Horizontal MC Movable Tool - holder
卧式加工中心可移动刀座的使用
ilib.cn
随便看

 

英汉双解词典包含2704715条英汉词条,基本涵盖了全部常用单词的翻译及用法,是英语学习的有利工具。

 

Copyright © 2004-2022 Newdu.com All Rights Reserved
更新时间:2024/12/25 13:14:44