| 单词 | shot-peening |
| 释义 | 例句释义: 〔机〕喷丸加工,喷丸硬化,微粒冲击平面法,喷丸强化 1. The surface residual stresses of the rolled workpieces can be reduced remarkably by shot peening. 滚压后再喷丸显著降低工件的表面残余压应力。 rjggy.net 2. The surface layer of shot peening strengthening was analyzed with OM, SEM and TEM. 采用金相显微镜、扫描电镜和透射电镜分析材料喷丸强化层。 www.ceps.com.tw 3. Great stress relief would occur in the uniform surface residual stress introduced by shot-peening with a great stress gradient. 喷丸引入的表层残余应力均匀且梯度大，主要发生应力松弛； www.rjggy.net 4. The surface nanocrystallization is approached on a commercial pure titanium by using high energy shot peening(HESP) technique. 用高能振动喷丸法对工业纯钛进行了表面纳米化的研究。 www.chemyq.com 5. Fatigue test was carried out for commercial pure titanium that have nano-crystallized in surface by high-energy shot peening. 采用高能喷丸方法使工业纯钛疲劳试样的表层实现纳米化，并进行了疲劳试验。 www.chemyq.com 6. Effect of pressure and time of shot peening on recrystallization of nickel base single crystal superalloy was studied. 研究了喷丸压力和喷丸时间对一种镍基单晶高温合金再结晶的影响。 www.chinamet.cn 7. Scoring or shot peening procedure shall be in accordance with the manufacturer's technology. 划痕或喷丸硬化过程要按生产厂家技术进行？ dictsearch.appspot.com 8. Familiar test with the heat treatment, shot peening. 熟悉热处理、喷丸的检验。 www.jobui.com 9. Shot Peening(SP)is a typical severe plastic deformation method to produce ultra-fine grains of metallic materials. 高能气动喷丸是通过剧烈塑性变形产生细晶材料的方法之一。 www.dictall.com 10. Aerospace industry. Shot peening for inducement of compressive surface stresses for metallic parts. 航空航天工业.金属部分压缩表面张力的诱导喷射冷锻处理 www.mapeng.net 1. The microhardness and surface roughness increase with the shot peening intensity increase. 硬度和粗糙度都随喷丸强度的增加而增大。 www.ceps.com.tw 2. The effect and mechanism mechanism of laser shot peening on improving metal resistance of stress corrosion cracking were analyzed in detail. 分析了激光喷丸技术对提高金属抗应力腐蚀开裂性能的效果和机理； www.jgjs.net.cn 3. In the present study, a three-dimensional FE model of shot peening process was developed using commercial software ABAQUS. 运用商用软件ABAQUS建立了铸钢钢丸冲击结构钢靶材的三维有限元模型。 lib.cqvip.com 4. The characterization of structure strengthening of different shot peening process for TC4-DT titanium alloys was studied. 研究了喷丸强化对TC4-DT钛合金材料组织的强化效果； www.ceps.com.tw 5. 8226; Shot peen technician is responsible for the preparation, setup and shot peening of aircraft components. 喷丸技术员的主要职责是飞机部件进行喷丸准备，设置和实施。 www.yjbys.com 6. Composite Technics of Shot - peening and Brush- plating for Renovating Gears . 直升机齿轮喷丸-电刷镀复合修复工艺研究。 www.bing.com 7. The proper shot peening process was presented on the basis of shot peening density and coverage test. 通过疲劳试验，得出了喷丸处理对弯曲疲劳强度和接触疲劳强度的影响程度。 www.chemyq.com 8. The gear fatigue test showed that shot peening can improve its strength significantly. 结果表明：喷丸处理能极大地提高齿轮的疲劳强度，从而提高齿轮的使用寿命。 www.chemyq.com 9. The feasibility of improving K417 fatigue life by surface shot peening and recrystallization was studied. 研究了采用喷丸再结晶方法提高K417合金疲劳寿命的可行性。 dictsearch.appspot.com 10. Based on the characteristic of thin aluminium skin, shot peening and peening forming, peening forming by double face is a new mixed process. 对喷成形技术是结合铝合金薄板件的特点，在喷丸成形和强化工艺基础上，提出的一种边缘工艺技术。 www.dictall.com 1. Experimental results indicated that the effect of shot-peening and ion implantation on the S-N curves is related to temperature. 结果表明，喷丸和离子注入对材料疲劳S-N曲线的影响与实验温度有关。 www.dictall.com 2. The working principle of laser shot peening was introduced. 介绍了激光喷丸技术的工作原理； www.jgjs.net.cn 3. Where to find a professional shot peening company in China? 中国哪里可以找到一家专业的喷丸加工厂？ goabroad.zhishi.sohu.com 4. The Engineering Calculation Method of the Optimum Residual Stress Field Introduced by Shot Peening into the Surface Layer of Spring 弹簧表层优化喷丸残余应力场的工程计算方法 www.ilib.cn 5. An Investigation on High Chromium Cast Iron Material Used for Blade of Shot Peening Machine 高铬铸铁叶片材质研究 ilib.cn 6. Application of Liquid Shot-peening at Strengthen the Surface of Turbine's Part 液体喷丸在汽轮机零件表面强化上的应用 ilib.cn 7. Shot Peening Strengthening of Track Pans Made of Medium Manganese Cast Steel 中锰铸钢坦克履带板连接筋的喷丸强化处理 www.ilib.cn 8. Study of Improvement on Contact Fatigue Strength of Carbonitriding Gears by Shot Peening 强力喷丸对提高碳氮共渗齿轮接触疲劳强度的研究 ilib.cn 9. Al. Investigation of surface nanocrystallization of a low carbon steelinduced by ultrasonic shot peening 低碳钢超声喷丸表面纳米化的研究 www.ilib.cn 10. Characterization of structure strengthening for shot peening affected layers of steels in hard state 硬状态钢喷丸影响层组织强化的表征 www.ilib.cn 1. Investigation on Grain Refinement Mechanism for High Energy Shot Peening Aluminium Alloy 高能喷丸铝合金表层晶粒细化机制研究 www.ilib.cn 2. Strengthening Technologies of Shot Peening on Metal Part Surface Modification 金属零件表面改性的喷丸强化技术 www.ilib.cn 3. Finite Element Analysis of Treatment Parameters of Shot-Peening for Hydraulic Machinery 提高水力机械抗磨蚀性能的喷丸工艺数值分析 www.ilib.cn 4. Finite Element Analysis for Shot-Peening Models of Single Shot Impact and Multiple Impingement 单丸粒喷丸模型和多丸粒喷丸模型的有限元模拟 www.ilib.cn 5. Numerical Simulation and Optimization For Shot Peening Forming Process of Panel with Stiffeners 板加筋壁板零件的喷丸成形数值模拟与工艺优化 www.ilib.cn 6. Experimentation of residual stresses of gear strengthened by shot peening 喷丸强化齿轮残余应力的实验研究 scholar.ilib.cn 7. Technology of Water Jet Shot Peening at High Pressure and Its Effective Factors 高压水射流对金属材料的喷丸强化及影响因素 service.ilib.cn 8. Effect of Surface Nanocrystallization on the Fatigue Properties of Commercial Pure Titanium Induced by High Energy Shot Peening 高能喷丸表面纳米化对工业纯钛疲劳性能的影响 ilib.cn 9. A Technological Test for Gear Surface Shot Peening Intensification 齿轮表面喷丸强化的工艺试验 service.ilib.cn 10. Microstructure changes and residual stresses of each phase caused by shot peening in 304 austenitic stainless steel 304奥氏体不锈钢喷丸引起的组织转变和两相残余应力测定 www.ilib.cn 1. Aerospace series - Adhesion test for metallic coatings by shot peening 航空航天系列用喷丸加工法作金属涂层的粘附性试验 www.mapeng.net 2. Deformation Twins in Shot-Peening Strengthening Layer of Pure Titanium 纯钛喷丸强化层中的变形孪晶 www.ilib.cn 3. Recent Trends on Surface Modification Technology of Shot Peening 喷丸表面改性技术的研究进展 ilib.cn 4. Research on technology of metal plate plastic forming by laser shot peening 激光喷丸成形金属板料的研究 www.ilib.cn 5. Study on Process Properties of Shot-peening and Parameters Control 喷丸加工的工艺特性及参数控制研究 www.ilib.cn 6. TEM investigation of surface nanocrystallization of Al alloy by ultrasonic shot peening 铝合金高能喷丸表层纳米化的TEM观察 www.ilib.cn 7. Investigation on the Shot Peening of Commercial Pure-Titanium 工业纯钛喷丸强化研究 www.ilib.cn 8. Measurement and Analysis of Residual Stress in Link Using Shot Peening 喷丸强化连杆残余应力的测试与分析 www.ilib.cn 9. Shot-Peening for Preventing From Corrosion of Aircraft Seat Track 喷丸强化用于飞机座椅轨道防腐 service.ilib.cn 10. Characteristics of Compressive Residual Stress Fields in High-strength Steel Caused by Shot Peening 高强度钢喷丸强化残余压应力场特征 service.ilib.cn 1. Shot peening and the selective application of air compressor (IV) 喷丸清理与空压机的选用（续三） www.ilib.cn 2. The Effective Factor and Application for Liquid Shot-peening for Turbine Part 液体喷丸效果的影响因素及应用 ilib.cn 3. The Effect of Plasma Nitriding and Shot Peening on the Fretting Damage Resistance of Ti Alloy 等离子渗氮与喷丸强化复合改进钛合金抗微动损伤性能 ilib.cn 4. Adhesion test for metallic coatings by shot peening 用喷丸加工法做金属覆层的附着力试验 www.mapeng.net 5. Shot Peening Process of Tail Strap of an Aircraft 某型飞机平尾带板的喷丸工艺 www.ilib.cn 6. The Effect of Controlled Shot-peening on the Cavitation in Hydraulic Turbines 受控喷丸对水轮机空蚀的作用 www.ilib.cn 7. Substance Transfer Phenomenon in the Process of High-Energy Shot Peening 高能喷丸过程中的物质转移现象 www.ilib.cn 8. The Effect of Shot Peening on the Strength of Gears in Automobile Transmission 喷丸处理对汽车变速箱齿轮疲劳强度影响的研究 www.ilib.cn 9. Mechanism of Shot Peening for Cemented Gear 渗碳齿轮的喷丸强化机理 www.ilib.cn 10. Shot peening on ultra-high strength steels 超高强度钢的喷丸强化 www.ilib.cn 1. Study on the Decarbruized Layer of the Spring Steel Before and After Shot Peening 喷丸前后板簧脱碳表层的研究 ilib.cn 2. Technology of Water Jet Shot Peening at High Pressure 高压水射流喷丸强化技术 www.ilib.cn |
| 随便看 |
|
英汉双解词典包含2704715条英汉词条，基本涵盖了全部常用单词的翻译及用法，是英语学习的有利工具。