单词 | pouring temperature |
释义 | 例句释义: 浇注温度,浇铸温度,填充温度 1. With the faster cooling rate, the slurry preparation time can be largely reduced by decreasing pouring temperature. 在冷速较快的情况下,降低浇注温度可以大大缩短半固态浆料的制备时间; www.csu.edu.cn 2. The results show that the depth and hardness of chill layer decreases with the elevation of the pouring temperature. 实验发现,随着浇注温度的升高,会导致凸轮桃尖白口层深度和硬度下降; www.ceps.com.tw 3. Increasing cooling rate of melt from the treated temperature to pouring temperature could decrease grain size. 随着熔体从处理温度降到浇注温度的冷却速率的增加,晶粒尺寸减小。 www.13191.com 4. The preheatingten1perature of model and porous matter, pouring temperature of metal liquid are the keys to the quality of sponge aluminium. 模具与多孔体的预热温度和浇属液的浇注温度是保证海绵铝质量的关键。 www.chemyq.com 5. As pouring temperature decreasing, primary phase in the alloy without RE addition changes from large dendritic crystal to equiaxed crystal. 未添加RE的合金,随浇注温度的下降,其初生相由发达的树枝晶转变成等轴枝晶。 rjggy.net 6. The greater flow rate of cooling water, the greater cooling intensity it will be, and need the higher pouring temperature. 水冷却流量越大,冷却强度越大,所需要的浇注温度也就越高。 paper.pet2008.cn 7. The pouring temperature of liquid metal need to be controlled and standardized. 需要控制铁水的出炉温度并将其标准化。 wenku.baidu.com 8. The higher the pouring temperature or the larger the sprue hollow area rate is , the faster the filling velocity of molten aluminum is. 浇注温度越高、直浇道空心面积率越大,铝液充型速度越快。 terms.shengwuquan.com 9. When pouring temperature is too low, the steel pipe may be blocked, lead to the experiment fail. 浇注温度过低,可能会堵塞钢管,导致实验失败。 paper.pet2008.cn 10. Under the precondition that no cold shut occurs, it creates conditions to decrease pouring temperature. 在不产生冷隔的前提下,为降低浇注温度创造了条件。 www.ceps.com.tw 1. With the decrease of pouring temperature, primary phase in the alloy with 0. 5% RE changes from dendritic crystal to spherical crystal. 添加了0.5%RE的合金,随浇注温度的降低,其初生相由树枝晶转变成细小的球状晶粒; rjggy.net 2. The effect of pouring temperature on the microstructure of chilled iron camshaft was studied. 研究了浇注温度对激冷铸铁凸轮轴组织性能的影响。 www.ceps.com.tw 3. The influence of chemical component. centrifugal time and pouring temperature on roll ring quality has been discussed. 文中叙述了化学成分、离心时间、浇注温度对辊套质量的影响。 www.chemyq.com 4. Along with pouring temperature's enhancement, the sufficient time and the setting time slightly have increase. 随着浇注温度的提高,充型时间和凝固时间都稍有增加; www.fabiao.net 5. How much pouring temperature of EPC should be improved than that of sand mould casting 消失模铸造的浇注温度应比砂型铸造提高多少 www.ilib.cn 6. Effects of Pouring Temperature and Mechanical Vibration on Microstructure and Mechanical Properties of Lost Foam Casting Magnesium Alloy 浇注温度和机械振动对消失模铸造镁合金组织和力学性能的影响 www.ilib.cn 7. Effects of Disturbing Condition and Pouring Temperature in Semisolid State on Microstructure of Magnesium Alloy 半固态温度区间扰动条件和浇注温度对镁合金铸态组织的影响 service.ilib.cn 8. different pouring temperature should be adopted for different moulds; 不同铸型宜选择不同的浇注温度; www.ceps.com.tw 9. Influence of Pouring Temperature on Primary Austenite in Semi-solid Hypoeutectic High Chromium Cast Iron 浇注温度对半固态亚共晶高铬铸铁初生奥氏体的影响 www.ilib.cn 10. Insufficient pouring temperature to promote proper collapsibility of sand and cores 浇注温度不足,促进砂子和芯子的溃散。 wenku.baidu.com 1. Select the Proper Pouring Temperature of Castings Depending on Mold Filling Simulation 依据充型模拟确定铸件浇注温度 www.ilib.cn 2. Effect of Pouring Temperature on the Structure of Ultrasonic Ingots 浇注温度对超声波细化铸锭组织的影响 www.ilib.cn 3. When pouring temperature is too high, the temperature of export aluminum is too high, and can not form a better semi-solid organization; 浇注温度过高,出口铝合金的温度过高,不能形成比较好的半固态组织; paper.pet2008.cn |
随便看 |
|
英汉双解词典包含2704715条英汉词条,基本涵盖了全部常用单词的翻译及用法,是英语学习的有利工具。