moulding

Extra mouldings are made up to supplement the standard left-hand-drive dashboard moulding to take a huge array of equipment.

It may also be used in a similar manner for multi-impression tubular shaped mouldings on underfeed and runner less moulds.

starting with a small gate width, the mould is tried out with a short injection stroke so that short mouldings are obtained.

This type of gate is used for tubular-type mouldings when more than one impression is required in a simple two-plate mould.

Rather than using physical mouldings to design a car, as remains a common practice today, for instance, this is all done online at AACE.

Plastics. Melamine-formaldehyde mouldings. Determination of extractable formaldehyde.

Thus, during the latter part of the opening stroke the ejector assembly is pulled. thereby ejecting the mouldings.

To achieve optimum coating quality, the maximum moisture content of the mouldings must be less than 0. 1%.

Fabricate frames, concealed stiffeners, reinforcement, edge channels, louvers and mouldings from either cold-rolled or hot-rolled steel.

The sill extensions are visually integrated front and rear with the scalloped corners of the new bumper mouldings .

The facade of the temple is exquisitely decorated with plaster mouldings and murals of auspicious motifs.

This gate is used for single-impression tubular shaped mouldings on two-plate moulds.

The new bumper mouldings are much deeper with curved, uninterrupted surfaces.

Why are we charging the customer 17% vat on mouldings, tooling yes but mouldings ?

TAB GATE This is a particular gating technique for feeding solid block-type mouldings.

We want to buy Gaskets, Fittings, Mouldings and Tubes, Fire Hoses Plastic Moulding.

Testing of Plastics; Hot Storage Test on Mouldings Made of Thermoplastic Moulding Materials without External Mechanical Stressing

Testing of Plastics; Heat Storage of Compression Mouldings Made of Thermosetting Compression Moulding Materials

Plastics - Phenol-formaldehyde mouldings - Determination of free ammonia and ammonium compounds - Colorimetric comparison method

Rough castings of light metal alloys - Sand mouldings - General tolerances, machining allowances; inactive for new design

Plastics - Phenol-formaldehyde mouldings - Determination of free ammonia and ammonium compounds - Indophenol method

Phenol-formaldehyde mouldings--Determination of free ammonia and ammonium compounds--Colorimetric comparison method

Plastics - Phenol-formaldehyde mouldings - Determination of free phenols - Iodometric method

Methods of testing plastics - Chemical properties - Determination of acetone-soluble matter in phenolic mouldings

Flexible cellular polymeric materials - Sponge and expanded cellular rubber products - Specification - Part 2: Mouldings and extrusions

Aerospace series - Glass fibre reinforced mouldings and sandwich composites - Production of test panels

Specification for glass fibre reinforcing mouldings and sandwich composites - Production of test panels

Plastics mouldings; Tolerances and acceptance conditions for linear dimensions

Code of practice for a system of tolerances for the dimensions of plastics mouldings

Determination of free phenols in phenol-formaldehyde mouldings--Iodometric method

Specification for phenolic mouldings for aeronautical purposes

Plastics - Phenol-formaldehyde mouldings - Detection of free ammonia

Aerospace; boron fibre reinforced mouldings, preparation of test laminates

Plastic over mouldings, composite plastics and metal components in the medical and domestic markets

Phenolic mouldings--Determination of acetone-soluble matter

Phenol-formaldehyde mouldings--Detection of free ammonia

Heated tool welding of thermoplastics mouldings in mass production

Insert nuts; heavy type for plastics mouldings and pressure die castings with dead hole

Closed Insert Nuts with Dead Hole for Plastics Mouldings

closed insert nuts with disc for plastics mouldings

Open Insert Nuts for Plastics Mouldings