单词 | internal clearance |
释义 | 例句释义: 内余隙,内部间隙,内部空间距离,内游隙 1. Normal internal clearance, normally only used together with an additional letter that identifies a reduced or displaced clearance range. 正常内部游隙,一般仅与另一个表示缩小或位移的游隙范围的字母一起使用。 www.skf.com 2. The axial internal clearance of the double row bearings is at least 0, 5 mm. 双列轴承的轴向内部游隙为至少0,5毫米。 www.skf.com 3. As the bearing is driven up the tapered seating, its radial internal clearance is reduced . 轴承径向内部游隙随着轴承在圆锥轴颈上的推进而缩小。 www.bing.com 4. CARB bearings are produced as standard with Normal radial internal clearance and most are also available with a larger C3 clearance . CARB轴承以常规径向内部游隙为标准制造,多数还备有游隙较大的C3组。 www.bing.com 5. Axial displacement of one ring relative to the other will gradually reduce the radial internal clearance in a CARB bearing. 一个套圈相对于另一套圈的轴向位移将逐渐减小CARB轴承中的径向内部游隙。 www.skf.com 6. It is also shown that increase of radial internal clearance may enhance nonlinearity of the system. 随着径向游隙的增大,转子系统的非线性特性增强; d.wanfangdata.com.cn 7. Therefore, under dynamic loads wear is naturally produced which enlarges the internal clearance. 因此,在动负荷下,很自然会发生磨损,从而增大内部游隙。 www.skf.com 8. Dimensions, tolerances and internal clearance of NoWear bearings are the same as for standard bearings. NoWear轴承的尺寸、公差和内部游隙与标准轴承相同。 www.skf.com 9. Rolling bearings. Radial internal clearance. 滚动轴承.径向内间隙 www.mapeng.net 10. The bearing sets of standard metric bearings are produced with the axial internal clearance provided in table 2 as standard . 标准公制轴承构成的轴承组在生产时带有如表2所列的标准轴向内部游隙。 www.bing.com 1. The spherical roller bearings of the metric SKF ConCentra units have C3 radial internal clearance. SKF公制ConCentra单元的球面滚子轴承具有C3径向内部游隙。 www.skf.com 2. Gap ? ? Taper Roller Bearing Internal Clearance is adjusted by Cone or Cup Spacer. 圆锥滚子轴承的内部间隙是由内圈或外圈隔圈来进行调整的 wenku.baidu.com 3. The axial internal clearance is determined by the sleeve. 轴向内部游隙取决于套筒。 www.skf.com 4. It looks like I should specify an approximate 30 micrometer internal clearance. 看起来我应该定义一个大约的30毫米以内的间隙。 www3.6sq.net 5. The narrow cam rollers have C3 radial internal clearance as standard . 标准的窄凸轮滚子有C3径向内部游隙。 www.bing.com 6. SKF split spherical roller bearings are manufactured with Normal or C3 radial internal clearance according to ISO 5753 : 1991 . SKF剖分式球面滚子轴承是根据1991年的ISO5753标准,以普通级或C3径向内部游隙制造的。 www.bing.com 7. C3 radial internal clearance to ISO 5753: 1991 (table 2). 标准C3径向内部游隙符合ISO5753:1991(表2)。 www.skf.com 8. SKF maintenance-free spherical plain bearings are produced with a radial internal clearance as per the following SKF免维护球面滑动轴承制造时采用下列径向内间隙 www.skf.com 9. Rolling bearings; tolerances for rolling bearings; radial internal clearance 滚动轴承.滚动轴承公差止推轴承的游隙 www.mapeng.net 10. Research and Calculation of Radial Internal Clearance about Offset Printing Cylinder's Rolling Bearing 胶印机滚筒滚动轴承径向游隙的研究与计算 scholar.ilib.cn 1. Distribution of Internal Gap Corresponding to Radial Internal Clearance of Rolling Bearing 滚动轴承径向游隙与内部间隙分布 ilib.com.cn 2. Factors Affecting Radial Internal Clearance of Operating High-Speed Rolling Bearing 高速旋转的滚动轴承工作游隙影响因素的分析 service.ilib.cn 3. Radial internal clearance of steel-on-PTFE composite material radial spherical plain bearings 钢对PTFE复合材料向心关节轴承径向游隙 www.ls.com.cn 4. The maximum permissible internal clearance or the maximum permissible friction has been reached (for bearings which require maintenance), or 当允许的最大内部游隙或最大摩擦(对需维护的轴承而言)达到后,或 www.skf.com 5. Application of FEA in Design of Radial Internal Clearance for Four Row Tapered Roller Bearing with Tapered Bore FEA在圆锥孔四列圆锥滚子轴承径向游隙设计中的应用 ilib.cn 6. Partial and One-piece Measurement of Axial Internal Clearance for Four-row Tapered Roller Bearings 四列圆锥滚子轴承轴向游隙的分体与整体测量 ilib.cn 7. Nonlinear Stability of Balanced Rotor Due to the Effect of Ball Bearing Internal Clearance 考虑径向内间隙的滚动轴承平衡转子系统的非线性动力稳定性 ilib.cn 8. The radial internal clearance of the bearing in operation, 轴承在运转时的径向内部游隙, www.skf.com 9. appropriate fits and bearing internal clearance or preload 装置间的适配及轴承间距或负载 bbs.translators.com.cn 10. The radial internal clearance limits are listed for bearings with 有关径向内部游隙的限值 www.skf.com 1. Axial internal clearance smaller than Normal 轴向内部游隙小于普通级 www.skf.com 2. Axial internal clearance greater than Normal 轴向内部游隙大于普通级 www.skf.com 3. Axial internal clearance in lower half of Normal range 轴向内部游隙在普通级范围的下半部分 www.skf.com 4. Axial internal clearance in upper half of C2 range 轴向内部游隙在C2范围的上半部分 www.skf.com |
随便看 |
|
英汉双解词典包含2704715条英汉词条,基本涵盖了全部常用单词的翻译及用法,是英语学习的有利工具。