in compression

When the ends move upwards relative to the centre the ship is said to "sag" and the deck is in compression while the bottom is in tension.

If the reverse is the case then the ship "hogs" with the deck in tension and the bottom in compression.

In compression molding the plastic material as powder or performs is placed into a heated steel mold cavity.

Environment protection monitor processing system. System installation guide is in compression documents.

Part crystallization phase affected the mechanical behavior and resulted an increase in hardness and an decrease in compression strength.

The recovery of set of compressed wood decreased with increases in compression set, heat treatment temperature, and time.

Now both sides of the cylinder are used to compress gas, one side being in suction when the other is in compression.

High fidelity in compression : advanced compression techniques deliver better quality content with small amount of information .

In compression zone bolt force of end-plate connections distribut triangularly, when designing calculating the force model can be referred .

It was shown that calculation strength agreed well with test results for joint specimens failed by forces of web in compression.

Numerical results show that the method has a more improvement in compression efficiency than the original algorithm.

RUBBER VULCANIZED. DETERMINATION OF TEMPERATURE RISE AND RESISTANCE TO FATIGUE IN COMPRESSION FLEXOMETER TESTING.

Flexible cellular polymeric materials. Determination of stress-strain characteristics in compression. Part 2 : high-density materials.

Polymeric materials, cellular flexible. Determination of stress-strain characteristic in compression. Part 1 : low-density materials.

It carries heat away from engine parts, clean engine parts, and helps the piston rings seal in compression pressure.

Set screws are stressed in compression and in action they create a helical wedge between the connected parts.

RUBBER, VULCANIZED. DETERMINATION OF CREEP IN COMPRESSION OR SHEAR.

Testing concrete in structures - Part 1 : cored specimens - Taking, examining and testing in compression.

For most materials the modulus of elasticity in compression is the same as in tension.

But stone in compression has great strength, and the Romans built huge stone bridges and aqueducts.

This stress, causing breakage, will be a tension since concretes are from 9 to 11 times as strong in compression as in tension.

Does a neutron star represent the ultimate in compression ?

I am CEO of a shareware company specialized in compression software.

Because of their relative simplicity, mold costs in compression molding are generally lower than in injection molding.

While glass is very strong in compression, tensile stresses will make these tiny fissures start to grow, bond by bond.

And this is very well known to engineers and architects , because it's a very strong surface in compression .

Polymeric materials, cellular flexible - Determination of stress-strain characteristic in compression - High-density materials

Polymeric materials, cellular flexible - Determination of stress-strain characteristic in compression - Low-density materials

Experimental and Modeling Study of Dimethyl Ether Combustion in Compression Ignition Engine

Experimental study of "ShaQima Framework" planting concrete in compression resistance and planting

Test Method for Vulcanized Rubber and Thermoplastic Elastomer-Determination of Force Decay (Stress Relaxation) in Compression

Adjacent-channel transient Rayleigh wave method and its application in compression strength test of water-tight wall

Analysis of Energy in Compression and Calcination During Soda Manufacturing

Flexible Cellular Polymeric Materials - Determination of Creep in Compression First Edition

Study on the Application of Dimethyl Ether Fuel in Compression-ignition Engine and Its Prospect

Polymeric materials, cellular flexible; Determination of stress-strain characteristics in compression; Part 1 : Low-density materials

Testing concrete in structures - Cored specimens - Taking, examining and testing in compression

Flexible cellular polymeric materials - Determination of creep in compression

Research on Microstructure Evolution and Deformation for Closed-Cell Aluminium Foams in Compression by SXR-CT Technique

Test methods of mechanical properties of mortar for ferrocement - Test for static modulus of elasticity in compression

Method for determination of the modulus of elasticity in compression perpendicular to grain of wood

Numerical Simulation of Non- steady Interaction Between Moving Bodies and Plasma in Compression Region

Standard Test Method for Plastics: Dynamic Mechanical Properties: In Compression

Evolvement of Methyl, Methane and Methanol During n-Heptane Combustion in Compression Ignition Engine

Analyzing and Verifying of the Forced Cylinder in Compression Refuse Collector

Well accept the state of high intensity work, strong in compression;

Rubber properties determination in compression or shear; (Yerzley mechanical oscillograph)

Stress-Strain Relationship of High-Strength Steel Fiber Reinforced Concrete in Compression

The experiment and modeling of dimethyl ether fuel injection process in compression ignition engine

Implementation of One Kind of Highly Effective Prediction Model in Compression Algorithm

Microstructure Evolution of Porous Foamed Aluminium in Compression

Testing of elastomers; determination of stress relaxation in compression

Standard Test Methods for Rubber Property-Heat Generation and Flexing Fatigue In Compression

The Density Damage Increment and Its Digital Image of Rock in Compression

A coding algorithm for facial image supporting feature extraction in compression-domain

The Application of Wavelet Neural Network in Compression and Reconstruction of Flaw Signals

Concrete; Determination of static modulus of elasticity in compression

Refractory products; determination of creep in compression

Test Methods for Rubber Property - Heat Generation and Flexing Fatigue in Compression

Rubber, vulcanized or thermoplastic - Determination of stress relaxation in compression at ambient and at elevated temperatures

Research on Modified Coefficient of Slenderness Ratio of Angle Member in Compression

Standard Test Method for Static Modulus of Elasticity and Poisson's Ratio of Concrete in Compression

Pre-Processing for High Resolution Video Acquisition in Compression

Short Period Rigidity and Deflection of Beams with Bonding Steel Plate in Compression Zone

Technical requirements of fire safety in compression chambers

Effect of short-term rigidity on precast reinforced concrete beam of side stuck steel in compression zone

Testing method for static modulus of elasticity and poission's ratio in compression of cylindrical concrete specimens

Analyses of the Failure Criteria of Masonry in Compression-Shear

Research and application of passing through method in compression test of mortar

The Improvement of National Power and Electronic Model in Compression Joint

The fold catastrophe model of constitutive failure in compression post

A Generic Stress- Strain Equation for Masonry Materials in Compression

The Assumption of Configuration of PLC in Compression Station on West-to-East Gas Pipeline

Methods of testing dense shaped refractory products - Part 9: Determination of creep in compression

The research on the application of combined-cycle in compression station

Rubber, vulcanized--Determination of stress relaxation in compression at normal and at elevated temperature

Wood; Testing in compression perpendicular to grain

refractory products - test method of creep in compression

Test method for creep in compression of refractory products

Test Methods for Rubber Properties in Compression

A Fast Algorithm to Detect Dissolve Shot in Compression Domain

Standard Test Method for Creep of Concrete in Compression

Effect of strain rate on dynamic behavior of concrete in compression

Method of testing in compression perpendicular to grain of wood

Testing method for creep of concrete in compression