injection pressure

In the function of injection pressure, the mould which has core will produce a little core offset and cause plastics deformation.

When the close time of the nozzles was set at the end of packing, the injection pressure, clamp force and parts quality were all better.

The injection pressure is commonly described as the surface pump pressure required to achieve injection.

Bad injected water quality have damaged formations and made injection pressure step up in Shasanzhong 6-10 low permeable reservoirs.

Theoretical result shows that even in a very low admixture injection pressure, fracturing will occur in surrounding soil.

The high pertinence between the weight of injection molding products and injection pressure is unveiled by experiments and analyses.

Maximum injection pressure and maximum holding pressure may be restricted due to molding condition.

Pollution in non-target zones can be reduced, the efficiency of profile control can be improved by using rational injection pressure.

When the nozzle is jammed, just remove it to clean. Keep in mind that clean obstruction by adding injection pressure is not permitted.

The simulation results of high-pressure fuel injection pressure are in relatively good agreement with the experimental ones.

Finally the empirical formula of reasonable water injection pressure and the research method of permeability differential were ensured.

Unlike in conventional systems, the injection pressure is independent of the engine speed.

Especially, to heterogeneity serious conglomerate reservoir, the control of injection pressure is more important.

The results show that effects of injection pressure, viscosity and the type of fluid on the permeability are not obvious.

part volume, runner-gate style and size, cavity locations, and injection pressure.

as fill time, injection pressure and pressure drop. With this result, users can avoid the.

According to the products and raw materials appropriate injection pressure and adjust injection speed.

At reservoir temperature and equal injection pressure, the order of 1. 2PV displacement efficiency is flue gas, nitrogen and air.

Injection pressure and holding pressure i.

The injection pressure went up quickly in the initial injection period in Ba 38 Block of Baolige Oilfield.

When injection, establishes the intensity of pressure in the screw rod forehead melt body to call the injection pressure;

propagation length of main crack in surrounding rock increases with the growth of horizontal stress coefficient and injection pressure;

Research on the Feasibility of Utilizing the System Dynamic Characteristic to Increase the Injection Pressure of the B-type Pump

Comprehensive comparison among various electronically controlled fuel injection systems with high injection pressure

Comparison of technical performance among electronically controlled fuel injection systems with high injection pressure

Fracture Analysis and Reasonable Injection Pressure Limit Definition of High Pressure Waterflooding Well

Research and Application of Decreasing Injection Pressure by Surfactant in Low- permeability Reservoir

Development and application of constant injection pressure automatic control system

Study on the Control Method of Injection Pressure of Electronically Controlled High-Pressure Common Rail Fuel Injection System

Establishment of reasonable water injection pressure of sandstone reservoir

Prediction of Injection Pressure and Melt Temperature of Injection Molding by Radial Basis Function Network

Simulation of Common-Rail Fuel Injection Pressure in Vehicle Diesel Engine and Strategy for Its Fuel Pressure Control

Requires high injection pressure and careful combustion development

Design of Continuous Flow Gas Lift Installations Using Injection Pressure Operated Valves

Experimental Research on Effect of Pulsatile Injection Pressure on Filling Cavity Pressure and Filling Time

Study on the Intelligent-Switch Fuzzy-PID Control for the Fuel Injection Pressure of Diesel Engines

A Test Analysis of Influence of Injection Pressure and Fuel Temperature for Standard Fuel Consumption

Effect of decreasing injection pressure of high-concentration polymer solutions

LDA Measurement of Droplet Velocities in a High Injection Pressure Diesel Fuel Spray

Method for Injection Pressure Prediction for Profile Control in Water Injection Wells

Study on Fuzzy Neural Network Control of Gas-injection Pressure in Gas-assisted Injection Molding

Study on PID Application of Gas-injection Pressure Curve in Gas-assistant Injection Molding

When injected in the screw head melt pressure built up by the said injection pressure;

The results show that, in the same volume of CO2 injection, the higher injection pressure, the greater the accumulated recovery;

Injection Pressure Control of GD-1 Electronically Controlled High-Pressure Common Rail Fuel Injection System

gas with high injection pressure can decrease the rudimental asphaltene in core;

High Injection Pressure capability independent of engine rpm

Influence of elastic effects on injection pressure of polymer flooding

Experimental Investigation on the Injection Pressure Control of Gd-1 High Pressure Common Rail Diesel Engine

Injection pressure of perforations varies

Excessively High Injection Pressure and Injection Speed is Too Fast

In order to better copy mould appearance, molding temperature should be proper high some, injection pressure, should do about big;

Effect of Pulsation Injection Pressure on Cavity Pressure

Adjust injection pressure and injection time

Laborotary Experiment of water injection pressure decreasing by surfactant

Well Testing with Injection Pressure Decline of Coal Bed Gas and Application of Shut in Well and Some Problems

The reason and countermeasures of high injection pressure of Chang - 8 oil block in Xifeng oilfield

Rely on high injection pressure to control emissions

The study shows that spray angle and injection pressure has highly significant effect on the workpiece surface roughness;

Low injection pressure, low clamp force

Injection pressure control system of die casting machine based on variable universe adaptive fuzzy

The study results indicate the bigger is the injection pressure, the lager is the transition zone of oil and gas;