holding time

Increasing the temperature and holding time of reheating, central carbon segregation can be improved a great deal.

The casting after cast can be fast cooled by the device, the holding time of the casting can be effectively shortened.

With the increase of the sintering holding time, the relative density of the compacts hardly increases, but the hardness could be improved.

Methods Of refrigerated transport Methods and insulation measures to observe the transit of drugs in refrigerated holding time of change.

A variable displacement pump could save energy during the long holding time.

Super Bowl Sunday has become an annual drama, and its holding time between the end of January early February.

Microstructure determined by both sintering temperature and high temperature holding time would influence acid corrosion resistance.

Attention: The holding pressure will affects the holding time. The higher holding pressure the longer holding time.

The size of primary grains decreases with increasing the vibration amplitude, and increases with increasing holding time.

Meanwhile, it was discovered that with longer holding time eutectic silicon particles got thicker and gathered.

The hardness increased, but the density, transverse rupture strength and compressive strength decreased when prolonging the holding time.

This paper discusses the influence of liquid adding rate, temperature holding time, flake treating manner and temperature on cladding rate.

The results showed that: appropriate calcining temperature and holding time were conducive to the activation of coal gangue.

The results show that quenching temperature, tempering temperature and holding time are determining factors.

The results show that heating temperature and holding time are two important factors affecting the grain size and uniformity.

The number and the size of voids would gradually be reduced to zero with enhancing heating temperature and holding time.

The refing effect decreased as the holding time of treated melt increased.

Inap- proriate sintering temperature and holding time will make a variety of defects, even destruct the electrode, cut down the performance.

With the isothermal holding time prolonged, the thick rod-like upper bainite associated and gradually developed into featherlike bainite.

With extend of holding time, growth stress is accumulated and crack appears gradually between oxide scale and matrix.

in heat-treatment process, SG modification can either shorten the holding time or lower the holding temperature.

With the extended holding time, Priority ferrites grow in austenite-ferrite interface.

Increasing the holding time in nanoindentation induces creep deformation, including transient stage creep and steady stage creep.

When remelted temperature and holding time are constant, with the increment of number times of extrusion the crystal grain becomes small.

The influence of synthesis temperature and holding time on synthesis was investigated.

The effect of vibration frequency and holding time on the shape coefficient of primary crystals and grain size was investigated.

The effect of holding time on intergranular phase and mechanical property of GPS silicon nitride ceramics was studied.

Due to the time necessary for measurement, the holding time at each temperature step was in the range between 15 and 20 h.

Is the max holding time between expose and develop documented and followed?

Temperature on the grain size and the proliferation carbon in martensite is much larger than the holding time.

The effects of sintering temperature, holding time, and milling time on the tribological properties were also studied.

everytime you launch a support - rocket , the holding time is extended by the time interval in which the fleet uses the deut.

While brazing temperature and holding time in excess would result in decline of joint shear strength.

Effect of Z-value and holding time on the products were investigated.

Effects of activation temperature, temperature holding time and activation agent ratio on the structure of adsorbents were investigated.

In 20 years, life in the most beautiful season of youth is a flower, the holding time, and we are the most beautiful Sheng of the owner.

The plasticized melt accumulates in front of the plunger. Only during injection (including holding time) is plasticizing stopped.

When the holding time is longer, the effects through a single extended holding time to reduce the yield strength is decreasing.

with this you can increase the holding time . normally the max . time how long a fleet can be hold is 32 hours.

Study on technological conditions such as sintering temperature holding time and the particle diameter which impact the whiteness.

No one can be young forever. So what we can do is holding time in our hands, trying our best to do what we think valuably.

holding time on gel property was no significant impact;

holding time of an international circuit

The results show that the higher the holding temperature, the faster the grains grow up and sphericize, the shorter the holding time;

Standard Practice for Estimation of Holding Time for Water Samples Containing Organic and Inorganic Constituents

controlling heating rate, keeping temperature and holding time by a heat treatment method to prepare the rare earth oxide nanobelt;

Standard Practice for Estimation of Holding Time for Water Samples Containing Organic Constituents

The results show that, under the same holding time, grain size and spheroidization increases with the increase of isothermal temperature;

Effects of Holding Time on Intergranular Phase and Mechanical Property of GPS Silicon Nitride Ceramics

Practice for Estimation of Holding Time for Water Samples Containing Organic Constituents

Influence of Quenching Temperature and Holding Time on Wear Resistance of Low Carbon-High Chromium Cast Iron

The results show that it can significantly improve powder quality through changing melt chamber gas and reducing holding time;

The effect of holding time on properties of porous ceramic support sintered at low temperature

Improve injection speed and holding time or pressure

Hardening Holding Time and Hardness Distribution of Hardened Layer by Plasma Surface Quenching

Effect of Holding Time on the Properties of Cordierite Ceramics

Relation Between Coating Thickness and Carbon Content and Holding Time in Carbon Steel's Mixed Salt Bath Vanadinizing

Holding time Injection alarm time

low current, holding time at tie-in is short

Holding time at test pressure

Mean Holding Time per Seizure

The holding time is proportional to the square of the metal thickness and opposited to the holding time;

Increase dose, holding time and holding pressure

Raise holding time and pressure