英语词汇tolerance value怎么读，是什么意思，单词翻译、读音、固定搭配用法和短语词组及例句-英汉双解词典

单词

tolerance value

释义

tolerance value

简明释义

容差值：在工程、科学和测量领域中，容差值是指一个测量值或参数允许的最大和最小偏差范围。

网络释义

1
?公称值
... 对称值 symmetry value 公称值 nominal value; tolerance value; value 焦点 1.[数学] [物理学] (二次曲线焦点; 主焦点) focal point; focus 虚焦点 virtual focus; 主焦点 principal focus; 焦点分散 defocus2.(问题的关键所在或争论的集中点) central issue; centre; point at issue 斗争的焦点 the focus of the struggle; 矛盾的焦点 focal points of contradictions; 问题的焦点 the heart of the matter; 争论的焦点 the points at issue3.[气象学] origin4.[冶金学] (焦斑) focal spot ...

短语

1
kauri tolerance value test
贝壳松脂稀释试验
2
biological tolerance value
生物耐受值
3
equal tolerance value method
相等公差值法

双语例句

1
Make sure that the Tolerance value is set to about 20 and that the Anti-alias and Contiguous options are checked as demonstrated below.
确保容差设在20左右，消除锯齿和连续是勾选上的，如下图。
2
Selection and calculation on tolerance value of symmetry construction were briefly introduced, some problems that should be paid attention to were also discussed.
扼要介绍有关对称结构尺寸公差值选择和计算以及在使用中应注意的问题。
3
In order to drop the product cost and improve the quality of products, this paper presents parameters and tolerance value and their determination method in the design of circuit.
为降低产品成本和提高产品质量，本文提出电路设计中参数和容差值同时确定方法。

随便看

英汉双解词典包含3185865条英汉词条，基本涵盖了全部常用单词的翻译及用法，是英语学习的有利工具。

单词	tolerance value
释义	tolerance value 简明释义容差值：在工程、科学和测量领域中，容差值是指一个测量值或参数允许的最大和最小偏差范围。网络释义 1 ?公称值 ... 对称值 symmetry value 公称值 nominal value; tolerance value; value 焦点 1.[数学] [物理学] (二次曲线焦点; 主焦点) focal point; focus 虚焦点 virtual focus; 主焦点 principal focus; 焦点分散 defocus2.(问题的关键所在或争论的集中点) central issue; centre; point at issue 斗争的焦点 the focus of the struggle; 矛盾的焦点 focal points of contradictions; 问题的焦点 the heart of the matter; 争论的焦点 the points at issue3.[气象学] origin4.[冶金学] (焦斑) focal spot ... 短语 1 kauri tolerance value test 贝壳松脂稀释试验 2 biological tolerance value 生物耐受值 3 equal tolerance value method 相等公差值法双语例句 1 Make sure that the Tolerance value is set to about 20 and that the Anti-alias and Contiguous options are checked as demonstrated below. 确保容差设在20左右，消除锯齿和连续是勾选上的，如下图。 2 Selection and calculation on tolerance value of symmetry construction were briefly introduced, some problems that should be paid attention to were also discussed. 扼要介绍有关对称结构尺寸公差值选择和计算以及在使用中应注意的问题。 3 In order to drop the product cost and improve the quality of products, this paper presents parameters and tolerance value and their determination method in the design of circuit. 为降低产品成本和提高产品质量，本文提出电路设计中参数和容差值同时确定方法。
随便看	Savannah Beach Savannah cat Savannah College of Art and Design Savannah monitor Savannah monitor savannah river savannah river plant savannah river savannahs Savannah Sparrow Savannakhet Selenduma Selene selenenic Selenenic acid selene Selene setapinnis selenetane selene unguium Selene vomer selenex Selenga Selenga River Selenge Selenge Aymang