Definition of pilot hole in English:

pilot hole

noun

A small hole drilled ahead of a full-sized hole as a guide.
导向孔；导洞；导坑
Example sentencesExamples
- If needed, drill a pilot hole before nailing to prevent the wood from splitting.
- They are put in place by drilling a hole through the mortar between the bricks (almost the entire width of the mortar) and then drilling a pilot hole in the block wall.
- If necessary, fill the old holes with wood filler and drill new pilot holes in the doors and cabinet frames.
- This requires using a brad-point bit with a smaller bit to drill a pilot hole.
- To avoid this, use a cordless drill to drill a pilot hole, one slightly smaller than the shank of the nail and then drive the nail into this.
- When the glue has dried, trim the dowel off flush with the cabinet, drill a small pilot hole into the end of the dowel, and reinstall the door with the original screws.
- Pull the hole saw out and begin drilling from the other side using the pilot hole as your center guide.
- Drill 1/8-inch holes through the templates at each pilot hole location.
- Drill a pilot hole with a 3/16-inch bit and insert the screw.
- Drill a pilot hole in plaster using the appropriate size masonry drill bit and tap in the anchor with the heel of a screwdriver or a hammer.
- A pilot hole is a hole drilled with a bit that is slightly thinner than the shank of the nail.
- Pre-drilling a pilot hole, slightly smaller than the nail thickness you will be using, prevents splitting the wood and is recommended for hardwoods (oak, maple, etc.) or near the ends of boards.
- Self-tapping screws have a special point that resembles a drill bit and are capable of cutting their own pilot hole in light gauge sheet metal.
- With attention now focused on the femur, the surgeon inserts a hollow, box osteotome in the femoral canal to create a pilot hole for femoral reaming instrumentation.
- If these simpler techniques are not working, try drilling a pilot hole through the board, nailing from above with a finishing nail, and then countersinking the nail and filling the hole with wood dough.
- Smaller screws have less chance of splitting wood, but if you're using larger screws and/or working near the end of a piece of wood then it's often safer to drill a pilot hole first.
- If the hole is stripped and the screw won't tighten, remove the screw and drill a deeper pilot hole for a new 3-in. screw that will extend into the framing behind the jamb.
- We like to drill a pilot hole into the stud to make installing the screw easier.
- What they do is to drill a pilot hole in the bolt, and place a bit into the hole that is reverse threaded so that while you are tightening up the bit, it is backing out the bolt.
- Drill a small hole through the plaster, called a pilot hole, and then attach a picture hook nail or other sturdy fastener using the hole.

Definition of pilot hole in US English:

pilot hole

noun

A small hole drilled as a guide for the insertion of a nail or screw, or for the drilling of a larger hole.
Example sentencesExamples
- This requires using a brad-point bit with a smaller bit to drill a pilot hole.
- When the glue has dried, trim the dowel off flush with the cabinet, drill a small pilot hole into the end of the dowel, and reinstall the door with the original screws.
- Smaller screws have less chance of splitting wood, but if you're using larger screws and/or working near the end of a piece of wood then it's often safer to drill a pilot hole first.
- If these simpler techniques are not working, try drilling a pilot hole through the board, nailing from above with a finishing nail, and then countersinking the nail and filling the hole with wood dough.
- Drill a pilot hole with a 3/16-inch bit and insert the screw.
- What they do is to drill a pilot hole in the bolt, and place a bit into the hole that is reverse threaded so that while you are tightening up the bit, it is backing out the bolt.
- Self-tapping screws have a special point that resembles a drill bit and are capable of cutting their own pilot hole in light gauge sheet metal.
- Pull the hole saw out and begin drilling from the other side using the pilot hole as your center guide.
- With attention now focused on the femur, the surgeon inserts a hollow, box osteotome in the femoral canal to create a pilot hole for femoral reaming instrumentation.
- A pilot hole is a hole drilled with a bit that is slightly thinner than the shank of the nail.
- Drill a small hole through the plaster, called a pilot hole, and then attach a picture hook nail or other sturdy fastener using the hole.
- If needed, drill a pilot hole before nailing to prevent the wood from splitting.
- Pre-drilling a pilot hole, slightly smaller than the nail thickness you will be using, prevents splitting the wood and is recommended for hardwoods (oak, maple, etc.) or near the ends of boards.
- If the hole is stripped and the screw won't tighten, remove the screw and drill a deeper pilot hole for a new 3-in. screw that will extend into the framing behind the jamb.
- If necessary, fill the old holes with wood filler and drill new pilot holes in the doors and cabinet frames.
- Drill a pilot hole in plaster using the appropriate size masonry drill bit and tap in the anchor with the heel of a screwdriver or a hammer.
- We like to drill a pilot hole into the stud to make installing the screw easier.
- They are put in place by drilling a hole through the mortar between the bricks (almost the entire width of the mortar) and then drilling a pilot hole in the block wall.
- To avoid this, use a cordless drill to drill a pilot hole, one slightly smaller than the shank of the nail and then drive the nail into this.
- Drill 1/8-inch holes through the templates at each pilot hole location.

单词	pilot hole
释义	Definition of pilot hole in English: pilot hole noun A small hole drilled ahead of a full-sized hole as a guide. 导向孔；导洞；导坑 Example sentencesExamples If needed, drill a pilot hole before nailing to prevent the wood from splitting. They are put in place by drilling a hole through the mortar between the bricks (almost the entire width of the mortar) and then drilling a pilot hole in the block wall. If necessary, fill the old holes with wood filler and drill new pilot holes in the doors and cabinet frames. This requires using a brad-point bit with a smaller bit to drill a pilot hole. To avoid this, use a cordless drill to drill a pilot hole, one slightly smaller than the shank of the nail and then drive the nail into this. When the glue has dried, trim the dowel off flush with the cabinet, drill a small pilot hole into the end of the dowel, and reinstall the door with the original screws. Pull the hole saw out and begin drilling from the other side using the pilot hole as your center guide. Drill 1/8-inch holes through the templates at each pilot hole location. Drill a pilot hole with a 3/16-inch bit and insert the screw. Drill a pilot hole in plaster using the appropriate size masonry drill bit and tap in the anchor with the heel of a screwdriver or a hammer. A pilot hole is a hole drilled with a bit that is slightly thinner than the shank of the nail. Pre-drilling a pilot hole, slightly smaller than the nail thickness you will be using, prevents splitting the wood and is recommended for hardwoods (oak, maple, etc.) or near the ends of boards. Self-tapping screws have a special point that resembles a drill bit and are capable of cutting their own pilot hole in light gauge sheet metal. With attention now focused on the femur, the surgeon inserts a hollow, box osteotome in the femoral canal to create a pilot hole for femoral reaming instrumentation. If these simpler techniques are not working, try drilling a pilot hole through the board, nailing from above with a finishing nail, and then countersinking the nail and filling the hole with wood dough. Smaller screws have less chance of splitting wood, but if you're using larger screws and/or working near the end of a piece of wood then it's often safer to drill a pilot hole first. If the hole is stripped and the screw won't tighten, remove the screw and drill a deeper pilot hole for a new 3-in. screw that will extend into the framing behind the jamb. We like to drill a pilot hole into the stud to make installing the screw easier. What they do is to drill a pilot hole in the bolt, and place a bit into the hole that is reverse threaded so that while you are tightening up the bit, it is backing out the bolt. Drill a small hole through the plaster, called a pilot hole, and then attach a picture hook nail or other sturdy fastener using the hole. Definition of pilot hole in US English: pilot hole noun A small hole drilled as a guide for the insertion of a nail or screw, or for the drilling of a larger hole. Example sentencesExamples This requires using a brad-point bit with a smaller bit to drill a pilot hole. When the glue has dried, trim the dowel off flush with the cabinet, drill a small pilot hole into the end of the dowel, and reinstall the door with the original screws. Smaller screws have less chance of splitting wood, but if you're using larger screws and/or working near the end of a piece of wood then it's often safer to drill a pilot hole first. If these simpler techniques are not working, try drilling a pilot hole through the board, nailing from above with a finishing nail, and then countersinking the nail and filling the hole with wood dough. Drill a pilot hole with a 3/16-inch bit and insert the screw. What they do is to drill a pilot hole in the bolt, and place a bit into the hole that is reverse threaded so that while you are tightening up the bit, it is backing out the bolt. Self-tapping screws have a special point that resembles a drill bit and are capable of cutting their own pilot hole in light gauge sheet metal. Pull the hole saw out and begin drilling from the other side using the pilot hole as your center guide. With attention now focused on the femur, the surgeon inserts a hollow, box osteotome in the femoral canal to create a pilot hole for femoral reaming instrumentation. A pilot hole is a hole drilled with a bit that is slightly thinner than the shank of the nail. Drill a small hole through the plaster, called a pilot hole, and then attach a picture hook nail or other sturdy fastener using the hole. If needed, drill a pilot hole before nailing to prevent the wood from splitting. Pre-drilling a pilot hole, slightly smaller than the nail thickness you will be using, prevents splitting the wood and is recommended for hardwoods (oak, maple, etc.) or near the ends of boards. If the hole is stripped and the screw won't tighten, remove the screw and drill a deeper pilot hole for a new 3-in. screw that will extend into the framing behind the jamb. If necessary, fill the old holes with wood filler and drill new pilot holes in the doors and cabinet frames. Drill a pilot hole in plaster using the appropriate size masonry drill bit and tap in the anchor with the heel of a screwdriver or a hammer. We like to drill a pilot hole into the stud to make installing the screw easier. They are put in place by drilling a hole through the mortar between the bricks (almost the entire width of the mortar) and then drilling a pilot hole in the block wall. To avoid this, use a cordless drill to drill a pilot hole, one slightly smaller than the shank of the nail and then drive the nail into this. Drill 1/8-inch holes through the templates at each pilot hole location.
随便看	separate school separate the men from the boys separate the sheep from the goats separate the sheep from the goats separate the wheat from the chaff separatical separating separation separation anxiety separationism separationisms separation of powers separation of powers separation order separations separatism separatisms separatist separatists separative separatives separator separators separatory separatory